Home > HEATING & COOLING > FIREPLACE & ACCESSORIES > STOVE PIPE & ACCESSORIES > CHIMNEY PIPE ACCESSORIES
Sort By:
1
Ameri-Vent 8RSC Double Wall Round Storm Collar Ameri-Vent 10RSC Double Wall Round Storm Collar Selkirk 208810 Storm Collar
Use with HS chimney roof flashing to insure water tight installation. Use with HS chimney roof flashing to insure water tight installation. Designed to fit on the round chimney pipe just above the roof flashing. The upper edge of the collar should be waterproofed with plastic sealer to prevent any water from leaking between the collar and chimney pipe. Part is tightened with screws or tabs after proper positioning.
Ultra Temp 208450 Type A Locking Band Selkirk 206810 Storm Collar Selkirk 206480 Finishing Collar
Ultra Temp Locking Band, Type A, Stainless Steel, 8 in Width, For use with Chimney Pipe Designed to fit on the round chimney pipe just above the roof flashing. The upper edge of the collar should be waterproofed with plastic sealer to prevent any water from leaking between the collar and chimney pipe. Part is tightened with screws or tabs after proper positioning. Round collar fits lower end of suspended insulated chimney pipe to provide finished appearance. Used to attach T-DSA Smoke Pipe Adapter to lower end of chimney or to insulated Tee.
AmeriVent 6SWA Single Wall Adapter Sure-Temp 206791 Spark Arrestor Selkirk 208480 Finishing Collar
Included in ceiling support assembly, roof support assembly and tee assembly. Diamond shaped 1/2" x 1" mesh, 18-8 stainless steel. Fits same size round chimney top. Keeps foreign objects out of chimney. Round collar fits lower end of suspended insulated chimney pipe to provide finished appearance. Used to attach T-DSA Smoke Pipe Adapter to lower end of chimney or to insulated Tee.
AmeriVent 8SWA Single Wall Adapter Sure-Temp 206465 Fire Stop/Joist Shield Sure-Temp 208790 Spark Arrestor
Included in ceiling support assembly, roof support assembly and tee assembly. Prevents or delays the rapid spread of fire (regardless of the cause) in a home or building. The sheet metal firestop prevents the chimney passageway from becoming an easy pathway for fire to spread from one floor to another. Diamond shaped 1/2" x 1" mesh, 18-8 stainless steel. Fits same size round chimney top. Keeps foreign objects out of chimney.
Sure-Temp 206520 Wall Band American Metal 6HS-SBA 3-Wall Wall Bracket Selkirk 206488 Trim Plate Spacer
Sure-Temp 206520 Wall Band
Our Price : $24.99
Used along the wall to provide for 2" clearance and assure stability. Useful for suspending offsets. Required at 8' or closer intervals to stabilize the chimney, wherever it is supported along a vertical wall. Bracket for supporting the chimney pipe offsets, securing outdoor chimney to exterior wall. Used to trim the ceiling when a chimney is supported from above and extended down into room. Also used in conjunction with firestop/joist shield.
FMI 12S-8DM 2-Wall Chimney Support Sure-Temp 208520 Wall Band American Metal 8HS-SBA 3-Wall Chimney Support Bracket Assembly
Sure-Temp 208520 Wall Band
Our Price : $31.99
Inner and outer pipe. The outer pipe, made of galvanized steel, provides cooling air necessary to maintain safe chimney temperatures, while the inner pipe, made of stainless steel, emits gases out of the fireplace. Snap- lock design. UL127 Listed. Up to 1700 Degree Pipe. Used along the wall to provide for 2" clearance and assure stability. Useful for suspending offsets. Required at 8' or closer intervals to stabilize the chimney, wherever it is supported along a vertical wall. Bracket for supporting the chimney pipe offsets, securing outdoor chimney to exterior wall.
FMI 30FS-8DM Fire Stop Spacer Sure-Temp 208465 Fire Stop/Joist Shield Ultra Temp 206450 Type A Locking Band
For Comfort Flame systems only. Prevents or delays the rapid spread of fire (regardless of the cause) in a home or building. The sheet metal firestop prevents the chimney passageway from becoming an easy pathway for fire to spread from one floor to another. Ultra Temp Locking Band, Type A, Stainless Steel, 6 in Width, For use with Chimney Pipe
Selkirk 206512 Adjustable Pitch Ceiling Plate American Metal 6FFU 3-Wall Round Roof Vent Flashing Selkirk 208512 Adjustable Pitch Ceiling Plate
Provides a finished appearance where the chimney passes through a sloped ceiling. Matte black finish. Adjusts to multiple roof pitches. Covers 4" space around chimney pipe (or 2" further than the required clearance). Standard flashings fit various pitch roofs. Its double seamed construction protects from water leakage. Provides a finished appearance where the chimney passes through a sloped ceiling. Matte black finish. Adjusts to multiple roof pitches. Covers 4" space around chimney pipe (or 2" further than the required clearance).
Selkirk 208488 Trim Plate Spacer Selkirk 206240 Drip less Smoke Stove Pipe Adapter Sure-Temp 206400 Anchor Plate
Used to trim the ceiling when a chimney is supported from above and extended down into room. Also used in conjunction with firestop/joist shield. For use in new installations, this part can be installed by twist-locking the coupler on the DSAC into the first section of Sure-Temp-Type HT chimney pipe. Provides a secure attachment for the chimney to smoke chamber outlet on masonry fireplaces, reducing footing loads and speeding construction. Stainless steel and heavy gauge steel construction for long life. Retains chimney with a twist-lock connection.
Sure-Temp 206435 Interior Resupport Selkirk 206242 Drip less Smoke Stove Pipe Adapter Selkirk 208240 Drip less Smoke Stove Pipe Adapter
Allows for two different methods of chimney resupport. First method is used at the immediate section of chimney above the upper elbow of an offset. Second method is used primarily when the immediate sections of the upper offset do not pass through a joist area and resupport is necessary. Support band is clamped around the chimney immediately below a locking band.  Straps are nailed to suitable framing at two inch clearance. For use in retrofit installations, this part can be installed from below with a finish support package and secured with screws. Note: Not for use with coal burning stoves. For use in new installations, this part can be installed by twist-locking the coupler on the DSAC into the first section of Sure-Temp-Type HT chimney pipe.
Selkirk A 206825 Adjustable Roof Flashing Sure-Temp 200420 Roof Support Sure-Temp 200250 Roof Support
Used to seal the opening where the chimney penetrates the roof and to direct rain and snow down from the roof and away from the chimney system. A series of adjustable flashings are available depending on your roof pitch. A flat and low pitch flashing is used to seal flat and low pitch roof (up to 2/12 pitch) openings. Fits all roof pitches and requires only simple framing. Brackets and mounting hardware only. Flexible roof support designed to fit 5, 6, 7, and 8" diameter chimney. The heavy duty band allows you to slide the length vertically to properly position this section in the system. The URSA can hold up to 30 feet of pipe, only 20 feet can be below.
American Metal 8FFU 3-Wall Round Roof Vent Flashing Sure-Temp 206430 Type HT Wall Support Kit Selkirk 208242 Drip less Smoke Stove Pipe Adapter
Standard flashings fit various pitch roofs. Its double seamed construction protects from water leakage. Tested for use fully enclosed and has been designed in 5, 6, 7 and 8 inch sizes to carry up to 60' of height. Intended for use with the Insulated Tee as an interior or exterior support where the chimney has a lateral connection. Also useful where the pipe connection passes through a combustible interior or exterior wall. Braces may only be fastened to the wall above or below the plate for chimneys which penetrate through the wall. For use in retrofit installations, this part can be installed from below with a finish support package and secured with screws. Note: Not for use with coal burning stoves.
Sure-Temp 206800 Round Type HT Chimney Topper Sure-Temp 208400 Anchor Plate Sure-Temp 206490 Attic Insulation Shield
Designed with a dome to exclude rain and leaves and a lower skirt to deflect wind for proper chimney draft. Provides a secure attachment for the chimney to smoke chamber outlet on masonry fireplaces, reducing footing loads and speeding construction. Stainless steel and heavy gauge steel construction for long life. Retains chimney with a twist-lock connection. Used wherever a ceiling support, finish support, firestop or joist shield is installed below an open attic. Required to guard against the hazard of blown-in or blanket insulation filling any framed opening or contacting the chimney and possible storage of combustibles against the chimney.
Selkirk A 208825 Adjustable Roof Flashing AmeriVent 6HS-WTP 3-Wall Chimney Wall Thimble Sure-Temp 208430 Type HT Wall Support Kit
Used to seal the opening where the chimney penetrates the roof and to direct rain and snow down from the roof and away from the chimney system. A series of adjustable flashings are available depending on your roof pitch. A flat and low pitch flashing is used to seal flat and low pitch roof (up to 2/12 pitch) openings. Used with tee branch and chimney section to provide proper clearance to combustible materials. Matte black painted surface for interior wall eliminates need for trim plate. Tested for use fully enclosed and has been designed in 5, 6, 7 and 8 inch sizes to carry up to 60' of height. Intended for use with the Insulated Tee as an interior or exterior support where the chimney has a lateral connection. Also useful where the pipe connection passes through a combustible interior or exterior wall. Braces may only be fastened to the wall above or below the plate for chimneys which penetrate through the wall.
Selkirk A 206830 Adjustable Roof Flashing Sure-Temp 206440 Roof Brace Kit American Metal 6HS-CSA 3-Wall Ceiling Support Assembly
Used to seal the opening where the chimney penetrates the roof and to direct rain and snow down from the roof and away from the chimney system. A series of adjustable flashings are available depending on your roof pitch. A flat and low pitch flashing is used to seal flat and low pitch roof (up to 2/12 pitch) openings. Chimney support, use whenever there is a need to stabilize the chimney above the roof level. The purpose of the bracing is to hold the chimney against wind load, and to prevent damage from static and sliding snow. It should be used, at a midpoint on the chimney. Bracket adjusts from 4' to 6'. Use when chimney is installed in standard ceiling. 6" and 8" sizes fit between regular 16" O.C. ceiling joists. For exposed beam ceiling installations, use Roof Support. Cartoned to contain stainless steel matte black single wall adaptor.
AmeriVent 8HS-WTP 3-Wall Chimney Wall Thimble Sure-Temp 208800 Round Type HT Chimney Topper Sure-Temp 208440 Roof Brace Kit
Used with tee branch and chimney section to provide proper clearance to combustible materials. Matte black painted surface for interior wall eliminates need for trim plate. Designed with a dome to exclude rain and leaves and a lower skirt to deflect wind for proper chimney draft. Chimney support, use whenever there is a need to stabilize the chimney above the roof level. The purpose of the bracing is to hold the chimney against wind load, and to prevent damage from static and sliding snow. It should be used, at a midpoint on the chimney. Bracket adjusts from 4' to 6'.
Sure-Temp 208490 Attic Insulation Shield FMI V6F-8DM Roof Flashing Selkirk A 208830 Adjustable Roof Flashing
Used wherever a ceiling support, finish support, firestop or joist shield is installed below an open attic. Required to guard against the hazard of blown-in or blanket insulation filling any framed opening or contacting the chimney and possible storage of combustibles against the chimney. For 12" standard and high temperature pipe. Used to seal the opening where the chimney penetrates the roof and to direct rain and snow down from the roof and away from the chimney system. A series of adjustable flashings are available depending on your roof pitch. A flat and low pitch flashing is used to seal flat and low pitch roof (up to 2/12 pitch) openings.
FMI 30E-8DM Offset and Return Elbow American Metal 8HS-CSA 3-Wall Ceiling Support Assembly Sure-Temp Ultra-Temp 206411 Round Ceiling Support
FMI Offset and Return Elbow, 8 in Nominal, 30 deg Offset, For Wood Burning at 1700 deg Standard Pipes Use when chimney is installed in standard ceiling. 6" and 8" sizes fit between regular 16" O.C. ceiling joists. For exposed beam ceiling installations, use Roof Support. Cartoned to contain stainless steel matte black single wall adaptor. With proper framing, ceiling supports provide at least 2" minimum clearance to combustibles at the support level and can carry up to 50' of vertical chimney height.
American Metal 6HS-RSA12 3-Wall Chimney Roof Support American Metal 6HS-WS 3-Wall Wall Support Sure-Temp Ultra-Temp 206410 Square Ceiling Support
For exposed-beam ceiling installations. Available in flat to 6/12 pitch (Standard) and for steeper pitches of 7/12 to 14/12. Can be used up to 22/12 with double wall connector. Use ceiling support when chimney is to be installed in standard ceiling. Contains stainless steel matte black single wall adaptor. With clean out, heavy gauge base support the chimney tee and chimney. Includes removable outer wall tee cap for clean-out. With proper framing, all ceiling supports provide at least 2" minimum clearance to combustibles at the support level and can carry up to 50' of vertical chimney height.
Sure-Temp Ultra-Temp 208410 Square Ceiling Support FMI V12F-8DM Roof Flashing Sure-Temp 206420 Type HT Roof Support Kit
With proper framing, all ceiling supports provide at least 2" minimum clearance to combustibles at the support level and can carry up to 50' of vertical chimney height. For 12" standard and high temperature pipe. Contains one 18" length of pipe, roof brackets and necessary hardware. Note: Not for use with coal burning stoves.
American Metal 8HS-RSA12 3-Wall Roof Support Sure-Temp Ultra-Temp 208411 Round Ceiling Support Sure-Temp 206600 Type HT Roof Termination Kit
For exposed-beam ceiling installations. Available in flat to 6/12 pitch (Standard) and for steeper pitches of 7/12 to 14/12. Can be used up to 22/12 with double wall connector. Use ceiling support when chimney is to be installed in standard ceiling. Contains stainless steel matte black single wall adaptor. With proper framing, ceiling supports provide at least 2" minimum clearance to combustibles at the support level and can carry up to 50' of vertical chimney height. Includes the basic components for a standard installation; CT - Round Top,  AF-6 - Adjustable Flashing, and SC - Storm Collar. 2/12 - 6-12 pitch.
Selkirk 206100 Insulated Chimney Tee with Tee Cap AmeriVent 8HS-RCS 3-Wall Round Vent Cap American Metal 6HS-RKS 3 Wall Round Fuel Kit
Used to start chimneys indoors or outdoors using a wall support assembly or a masonry pier. A length of insulated chimney pipe is attached to the Tee snout, using a Locking Band, to pass safely through combustible walls. An Insulated Tee Cap is included which can be removed from bottom opening for inspection and cleanout. Maximum height of chimney which can be supported by an insulated Tee is 50'. Round termination features its own built-in spark arrestor. Protects against rain, debris and birds entering chimney. Built to last with a system combining corrosion resistant stainless steel and sturdy galvanized steel. It features a space-age ceramic fiber refractory blanket to withstand intermittent temperatures up to 2100 degrees F, is  noncombustible, thin and lightweight. It features the same small outer dimensions and is compatible with the AmeriVent Model FB. It is light enough to be easily installed by one man. Kit contains stainless steel cap, standard flashing, storm collar, ceiling support and single wall adaptor.
BOOT FLSHNG KIT RUB 12/12PITCH Selkirk A 206835 Adjustable Roof Flashing Sure-Temp 208420 Type HT Roof Support Kit
Used for installations on corrugated roofs flat to 12/12/ pitch. Kit includes rubber boot (23 4/5? x 21 ??), spacers kit, special storm collar, and mounting screws. Note: For an 8? chimney the maximum pitch is 10/12. Used to seal the opening where the chimney penetrates the roof and to direct rain and snow down from the roof and away from the chimney system. A series of adjustable flashings are available depending on your roof pitch. A flat and low pitch flashing is used to seal flat and low pitch roof (up to 2/12 pitch) openings. Contains one 18" length of pipe, roof brackets and necessary hardware. Note: Not for use with coal burning stoves.
FMI CP-8DM Chimney Pack Sure-Temp 208600 Type HT Roof Termination Kit Selkirk 208100 Insulated Chimney Tee with Tee Cap
Roof flashing with 24" base, firestop spacer, round termination cap, storm collar and flue extension. Fits standard 8" inner diameter, 12-3/8" outer diameter, 1700 degree pipe. Includes the basic components for a standard installation; CT - Round Top,  AF-6 - Adjustable Flashing, and SC - Storm Collar. 2/12 - 6-12 pitch. Used to start chimneys indoors or outdoors using a wall support assembly or a masonry pier. A length of insulated chimney pipe is attached to the Tee snout, using a Locking Band, to pass safely through combustible walls. An Insulated Tee Cap is included which can be removed from bottom opening for inspection and cleanout. Maximum height of chimney which can be supported by an insulated Tee is 50'.
American Metal 8HS-RKS 3 Wall Round Fuel Kit Sure-Temp 206620 Flat Ceiling Support Kit Sure-Temp 206621 Pitched Ceiling Support Kit
Built to last with a system combining corrosion resistant stainless steel and sturdy galvanized steel. It features a space-age ceramic fiber refractory blanket to withstand intermittent temperatures up to 2100 degrees F, is  noncombustible, thin and lightweight. It features the same small outer dimensions and is compatible with the AmeriVent Model FB. It is light enough to be easily installed by one man. Kit contains stainless steel cap, standard flashing, storm collar, ceiling support and single wall adaptor. Provides the support package and termination parts for a chimney that is supported by a flat ceiling and that passes through an attic area and penetrates the roof. Just add pipe lengths and the kit has all necessary parts for complete installation. Contents: Round top, Attic insulation shield, Storm collar, Finish support package, Adjustable flashing and Smoke pipe adapter. For installation of a chimney in a cathedral or pitched ceiling such as standard A-Frame construction. Provides all necessary parts for a complete installation with the exception of the required insulated pipe lengths and an adjustable flashing. Selection of the adjustable flashing is determined by the pitch of your roof and ceiling. Contents: Round top, Smoke pipe adapter, Storm collar, Finishing collar, Adjustable pitch ceiling plate and Roof support package.
Sure-Temp 208621 Pitched Ceiling Support Kit Ameri-Vent 6HS-030 3-Wall Chimney Pipe Offset AmeriVent 6HS-TA 3-Wall Chimney Tee Assembly
For installation of a chimney in a cathedral or pitched ceiling such as standard A-Frame construction. Provides all necessary parts for a complete installation with the exception of the required insulated pipe lengths and an adjustable flashing. Selection of the adjustable flashing is determined by the pitch of your roof and ceiling. Contents: Round top, Smoke pipe adapter, Storm collar, Finishing collar, Adjustable pitch ceiling plate and Roof support package. For use in pairs to permit chimney to "go around" joists, rafters, or other projections. Add chimney section between offsets to produce additional offset. Chimney tee, tee branch (made up of one 12" section of chimney), single wall adaptor, pipe end plate and tee cap. Use this combination where connection to chimney is made in branch of tee in Through-the-Wall installation.
Sure-Temp 208620 Flat Ceiling Support Kit Ameri-Vent 8HS-030 3-Wall Chimney Pipe Offset AmeriVent 8HS-TA 3-Wall Chimney Tee Assembly
Provides the support package and termination parts for a chimney that is supported by a flat ceiling and that passes through an attic area and penetrates the roof. Just add pipe lengths and the kit has all necessary parts for complete installation. Contents: Round top, Attic insulation shield, Storm collar, Finish support package, Adjustable flashing and Smoke pipe adapter. For use in pairs to permit chimney to "go around" joists, rafters, or other projections. Add chimney section between offsets to produce additional offset. Chimney tee, tee branch (made up of one 12" section of chimney), single wall adaptor, pipe end plate and tee cap. Use this combination where connection to chimney is made in branch of tee in Through-the-Wall installation.
Sure-Temp 206622 Thru-the-Wall Support Kit American Metal 6HS-TWK 3-Wall Chimney Installation Kit Sure-Temp 208622 Thru-the-Wall Support Kit
For a wall-supported chimney system with a horizontal connector passing through an exterior wall, connecting to a Tee and running vertically up the exterior wall to termination above the roof line. Provides all necessary parts for a complete installation with the exception of required insulated pipe lengths to reach your desired chimney height. Contents: Round top, 12'' Insulated pipe length, Wall band, Insulated tee/plug, Finishing collar, Wall support kit, Smoke pipe adapter and Insulated wall thimble. Designed for venting appliances through a side wall. Complete wall support components. Provides all-weather protection. For a wall-supported chimney system with a horizontal connector passing through an exterior wall, connecting to a Tee and running vertically up the exterior wall to termination above the roof line. Provides all necessary parts for a complete installation with the exception of required insulated pipe lengths to reach your desired chimney height. Contents: Round top, 12'' Insulated pipe length, Wall band, Insulated tee/plug, Finishing collar, Wall support kit, Smoke pipe adapter and Insulated wall thimble.
   
 
1