|
|
|
|
|
|
|
|
|
|
|
All brass, resists rust and will not corrode as easily as other materials. Precision machined to high quality standards. Use with hose clamp or ferrules.
|
All brass, corrosion resistant material. Connects FPT to FPT. With ball socket.
|
Recognized by the extremely short pilot. Has the widest metal section between the ball groove and the pilot. The sealing surface on the end of the nipple is wider than other interchanges, resulting in better sealing and longer seal life. Intended for compressed air lines only. 300 PSI maximum rated working pressure.
|
|
|
|
|
|
|
|
|
|
|
|
|
Nipple design is considered the industrial standard. Identified by the 3/16" pilot and flat bottom V-shaped ball groove. Intended for compressed air lines only. 300 PSI maximum rated pressure.
|
Nipple design is considered the industrial standard. Identified by the 3/16" pilot and flat bottom V-shaped ball groove. Intended for compressed air lines only. 300 PSI maximum rated pressure.
|
Identified by a 5/16" pilot and nearly round ball groove. Similar appearance to the Industrial Interchange and care must be taken to correctly identify. Intended for compressed airlines only. 300 PSI maximum rated working pressure.
|
|
|
|
|
|
|
|
|
|
|
|
|
Identified by a 5/16" pilot and nearly round ball groove. Similar appearance to the Industrial Interchange and care must be taken to correctly identify. Intended for compressed airlines only. 300 PSI maximum rated working pressure.
|
Properly seals all male threaded connections to prevent air leaks.
|
All brass, corrosion resistant material. Allows user to adjust thread sizes from 1/4" NPT through 3/8" NPT with either male or female ends.
|
|
|
|
|
|
|
|
|
|
|
|
|
Recognized by the extremely short pilot. Has the widest metal section between the ball groove and the pilot. The sealing surface on the end of the nipple is wider than other interchanges, resulting in better sealing and longer seal life. Intended for compressed air lines only. 300 PSI maximum rated working pressure.
|
All brass, resists rust and will not corrode as easily as other materials. Precision machined to high quality standards. Use with hose clamp or ferrules.
|
All brass, resists rust and will not corrode as easily as other materials. Precision machined to high quality standards. Use with hose clamp or ferrules.
|
|
|
|
|
|
|
|
|
|
|
|
|
All brass construction resists rust and will not corrode as easily as other materials. Precision machined to high quality standards. Use with hose clamp or ferrules.
|
Pipe couplings,thread adapters and bushings allows user to adjust thread sizes from 1/8" NPT through 1/2" NPT with either male or female ends. Corrosion resistant material. Connects FPT to FPT.
|
Most easily recognized design. Distinctive, long 3/4" pilot can not be confused with any other designs. Intended for compressed air lines only. 300 PSI maximum rated working pressure.
|
|
|
|
|
|
|
|
|
|
|
|
|
All brass, resists rust and will not corrode as easily as other materials. Precision machined to high quality standards. Use with hose clamp or ferrules.
|
Nipple design is considered the industrial standard. Identified by the 3/16" pilot and flat bottom V-shaped ball groove. Intended for compressed air lines only. 300 PSI maximum rated pressure.
|
Recognized by the extremely short pilot. Has the widest metal section between the ball groove and the pilot. The sealing surface on the end of the nipple is wider than other interchanges, resulting in better sealing and longer seal life. Intended for compressed air lines only. 300 PSI maximum rated working pressure.
|
|
|
|
|
|
|
|
|
|
|
|
|
All brass, resists rust and will not corrode as easily as other materials. Precision machined to high quality standards. Use with hose clamp or ferrules.
|
All brass, resists rust and will not corrode as easily as other materials. Precision machined to high quality standards. Use with hose clamp or ferrules.
|
Pipe coupling allows user to adjust thread sizes from 1/8" NPT through 1/2" NPT with either male or female ends. Corrosion resistant material. Connects MPT to MPT.
|
|
|
|
|
|
|
|
|
|
|
|
|
Plated steel; corrosion resistant steel for long life.
|
Most easily recognized design. Distinctive, long 3/4" pilot can not be confused with any other designs. Intended for compressed air lines only. 300 PSI maximum rated working pressure.
|
Recognized by the extremely short pilot. Has the widest metal section between the ball groove and the pilot. The sealing surface on the end of the nipple is wider than other interchanges, resulting in better sealing and longer seal life. Intended for compressed air lines only. 300 PSI maximum rated working pressure.
|
|
|
|
|
|
|
|
|
|
|
|
|
All brass construction resists rust and will not corrode as easily as other materials. Precision machined to high quality standards. Use with hose clamp or ferrules.
|
Connects FPT to FPT. Use thread sealant tape on all male threads for air tight connections.
|
Has a built in shut off valve and therefore cannot be used on inflator gauges. Use when air supply lines come directly from the compressor with no other valve in the line.
|
|
|
|
|
|
|
|
|
|
|
|
|
Has a built-in shut-off valve and therefore cannot be used on inflator gauges. Use when air supply lines come directly from the compressor with no other valve in the line. Automatic inflators use direct air line chucks.
|
Combination No. 17-350 chuck with 1/4" ID hose barb No. 21-123. Has a built-in shut-off valve and therefore cannot be used on inflator gauges. Use when air supply lines comes directly from the compressor with no other valve in the line. Automatic inflators use direct air line chucks.
|
Plated steel construction with drag guard for job site durability and reliability. Large body size for maximum air flow and tool performance. Corrosion resistant steel for long life.
|
|
|
|
|
|
|
|
|
|
|
|
|
Plated steel construction with drag guard for job site durability and reliability. Pre applied thread sealant for airtight connections.
|
Plated steel construction with drag guard for job site durability and reliability. Pre applied thread sealant for airtight connections. Eight ball coupler design for balanced, strong, secure connections.
|
Recognized by the extremely short pilot. Has the widest metal section between the ball groove and the pilot. The sealing surface on the end of the nipple is wider than other interchanges, resulting in better sealing and longer seal life. Intended for compressed air lines only. 300 PSI maximum rated working pressure.
|
|
|
|
|
|
|
|
|
|
|
|
|
Swivel design minimizes hose twisting for improved control. Corrosion-resistant steel. Pre-applied thread connections.
|
Snap-On Chuck Clip. Converts any single foot chuck to a clip-on chuck. Fits all standard ball foot chucks with .672-32 thread. Holds chuck to tire valve while inflating.
|
Due to their large size, do not connect or disconnect if the line pressure exceeds 40 PSI. Intended for compressed air lines only. 300 PSI maximum rated working pressure.
|
|
|
|
|
|
|
|
|
|
|
|
|
Couplers are intended for use on compressed air lines only. All have maximum rated working pressure of 300 PSI.
|
Pre-applied thread sealant for airtight connections. Simplifies field installation by eliminating the need for thread sealant tape. Plated steel construction with drag guard for jobsite durability and reliability. 6-ball design 1/4 coupler for balanced, strong and secure connections.
|
Pre-applied thread sealant for airtight connections. Simplifies field installation by eliminating the need for thread sealant tape. Plated steel construction with drag guard for jobsite durability and reliability. 6-ball design 1/4 coupler for balanced, strong and secure connections.
|
|
|
|
|
|
|
|
|
|
|
|
|
Utilizes the tubular valve which supports the seal and allows more air flow at lower pressure drops than most competitive couplers. Protective collar guards against accidental disconnect. Due to their large size, do not connect or disconnect if the line pressure exceeds 40 PSI. Intended for compressed air lines only. 300 PSI maximum rated working pressure.
|
Utilizes the tubular valve which supports the seal and allows more air flow at lower pressure drops than most competitive couplers. Protective collar guards against accidental disconnect. Due to their large size, do not connect or disconnect if the line pressure exceeds 40 PSI. Intended for compressed air lines only. 300 PSI maximum rated working pressure.
|
Hardened stainless steel locking balls for maximum performance. Corrosion resistant steel for long life. Pre-applied thread sealant for air tight connections.
|
|
|
|
|
|
|
|
|
|
|
|
|
Plated steel construction with drag guard for job site durability and reliability. Six ball coupler design for balanced, strong, secure connections. Corrosion resistant steel for long life.
|
Adjust from low air to a full volume flow. Recommended air pressure to 150 PSI maximum. Knurled nozzle makes handling easy. Complete with handy pocket clip. Fits all Industrial/Milton Design 1/4" coupler bodies.
|
Intended for compressed air lines only. 300 PSI maximum rated working pressure. Includes one each: No.12-225 1/4" Male NPT Plug and No.13-235 1/4" Female NPT Coupler. Design is considered the industrial standard. Identified by the 3/16" pilot and flat bottom V-shaped ball groove. Due to their large size, do not connect or disconnect if the line pressure exceeds 40 PSI.
|
|
|
|
|
|
|
|
|
|
|
|
|
Built-in shut-off valve cannot be used on inflator gauges. Use when air supply lines come directly from the compressor with no other valve in the line. Automatic inflators use direct air line chucks. Extension for hard-to-reach dual wheel valves on tractors, trucks or bus.
|
Contains all parts necessary to repair a direct air line hose assembly. Each kit contains: (1) Single Foot Air Chuck, 1/4" Female NPT, (1) Male Hose End 1/4" ID hose x 1/4" NPT, (1) Hose Splicer, 1/4" ID hose, (3) Band Style Hose Clamps, fits 3/8" ID hose
|
Vented nozzle to relieve the compressed air should the nozzle become plugged or accidentally obstructed. Heavy duty die cast body. Hang up hook and 1/4" NPT female inlet included. Meets OSHA regulation 1001 for 30 PSI "dead head'' pressure. Inlet Pressure - 150 PSI.
|
|
|
|
|
|
|
|
|
|
|
|
|
Six hardened stainless steel locking balls for maximum performance. Corrosion resistant steel for long life.
|
Kit Includes: (1) 1/4" MPT x barbed hose splicer for 3/8" hose ; (1) barb x barb hose splicer for 3/8" hose & (3) Clamps.
|
Turn ball type drain valve. 1/4" NPT male thread.
|
|
|
|
|
|
|
|
|
|
|
|
|
Due to their large size, do not connect or disconnect if the line pressure exceeds 40 PSI. Intended for compressed air lines only. 300 PSI maximum rated working pressure.
|
Eliminates kinked and twisted air line hose by swiveling a full 360 degrees. Use on air lines, tools, and compressor connections to increase flexibility and convenience. 150 PSI maximum working pressure.
|
Due to their large size, do not connect or disconnect if the line pressure exceeds 40 PSI. Intended for compressed air lines only. 300 PSI maximum rated working pressure.
|
|
|
|
|
|
|
|
|
|
|
|
|
Combination No. 17-350 chuck with No. 17-355 chuck clip. Has a built-in shut-off valve and therefore cannot be used on inflator gauges. Use when air supply lines come directly from the compressor with no other valve in the line. Automatic inflators use direct air line chucks.
|
Stanley Tee Fitting, 1/4 in Nominal, FNPT End, Brass
|
Intended for compressed air lines only. 300 PSI maximum rated working pressure. Includes one each: No.12-325 1/4" Male NPT Plug and No.13-335 1/4" Female Coupler. Identified by a 5/16" pilot and nearly round ball groove. Similar appearance to the Industrial Interchange and care must be taken to correctly identify. Due to their large size, do not connect or disconnect if the line pressure exceeds 40 PSI.
|
|
|
|
|
|
|
|
|
|
|
|
|
Intended for compressed air lines only. 300 PSI maximum rated working pressure. Includes one each: No.12-125 1/4" Male NPT Plug and No.13-135 1/4" Female NPT Coupler. Recognized by the extremely short pilot. Has the widest metal section between the ball groove and the pilot. The sealing surface on the end of the nipple is wider than other interchanges, resulting in better sealing and longer seal life. Utilizes the tubular valve which supports the seal and allows more air flow at lower pressure drops than most competitive couplers. Protective collar guards against accidental disconnect. Due to their large size, do not connect or disconnect if the line pressure exceeds 40 PSI.
|
Safety blow gun.
|
Has a built-in shut-off valve and therefore cannot be used on inflator gauges. Use when air supply lines come directly from the compressor with no other valve in the line. Automatic inflators use direct air line chucks. Works like a ``quick coupler". Snaps onto any standard tire valve and stays put until released.
|
|
|
|
|
|
|
|
|
|
|
|
|
Due to their large size, do not connect or disconnect if the line pressure exceeds 40 PSI. Intended for compressed air lines only. 300 PSI maximum rated working pressure. Available in sleeve type only.
|
Converts any standard ball foot tire chucks to a safety blowgun. Vented nozzle and built-in pressure reduces limit nozzle pressure to a maximum of 30 PSI, with up to 150 PSI inlet pressure. Conforms to No.1001 OSHA regulation. Epoxy finish.
|
Die-cast body. 1/4" air inlet.
|
|
|
|
|
|
|
|
|
|
|
|
|
3 piece 1/4" MPT quick plug; 1 piece 1/4" FPT quick plug; 1 piece 1/4"NPT quick coupler.
|
Due to their large size, do not connect or disconnect if the line pressure exceeds 40 PSI. Intended for compressed air lines only. 300 PSI maximum rated working pressure. Available in sleeve type only.
|
Couplers are intended for use on compressed air lines only. All have maximum rated working pressure of 300 PSI.
|
|
|
|
|
|
|
|
|
|
|
|
|
(1) One Each: 1/4" FPT Coupler (13-235), 1/4" MPT Coupling (21-505), 1/4" MPT Plug (12-225) and 1/4" FPT Plug (12-235).
|
Meets OSHA regulation 100-1 for 30 PSI "dead head" pressure. Features vented nozzle to relieve the compressed air should the nozzle become plugged or accidentally obstructed. Heavy duty die cast body with hang-up hook, 1/4" NPT female inlet, and 4" extension.
|
Utilizes the tubular valve which supports the seal and allows more air flow at lower pressure drops than most competitive couplers. Protective collar guards against accidental disconnect. Due to their large size, do not connect or disconnect if the line pressure exceeds 40 PSI. Intended for compressed air lines only. 300 PSI maximum rated working pressure.
|
|
|
|
|
|
|
|
|
|
|
|
|
Utilizes the tubular valve which supports the seal and allows more air flow at lower pressure drops than most competitive couplers. Protective collar guards against accidental disconnect. Due to their large size, do not connect or disconnect if the line pressure exceeds 40 PSI. Intended for compressed air lines only. 300 PSI maximum rated working pressure.
|
Oil resistant, soft replaceable rubber tip. Will not mar delicate surfaces. Ideal for leak proof seal against oil passages, fuel lines and carburetors when air pressure is needed for cleaning. Allows full line pressure to be used. Includes 1/4" female NPT inlet. To comply with OSHA regulations standard blowguns must be used on a regulated air line with a pressure setting not to exceed 30 PSI.
|
Conforms to all Federal requirements related to OSHA, including noise level regulations. Tamper proof pressure reducers built into this gun limit nozzle pressure to 30 PSI or less when used with listed inlet pressure. Features vented nozzle to relieve the compressed air should the nozzle become plugged or accidentally obstructed. Heavy duty die cast, epoxy finish body. Complete with hang-up hook and 1/4" female NPT inlet.
|
|
|
|
|
|
|
|
|
|
|
|
|
Increased performance and yet still meets OSHA regulation 100-1 for 30 PSI 'dead head' pressure. Features vented nozzle to relieve the compressed air should the nozzle become plugged or accidentally obstructed. Heavy duty die cast body. Complete with hang-up hook and 1/4" NPT female inlet. Inlet pressure 150 PSI.
|
Accepts 3/8" series Industrial Interchange or 3/8" Automotive Interchange plugs. Eight Hardened stainless steel locking balls for maximum performance.
|
Accepts 3/8" series Industrial Interchange or 3/8" Automotive Interchange plugs. Eight Hardened stainless steel locking balls for maximum performance.
|
|
|
|
|
|
|
|
|
|
|
|
|
Pre-applied sealant for airtight connections. Simplifies field installation by eliminating the need for thread sealant tape. Plated steel construction with drag guard for jobsite durability and reliability. 6-ball coupler design for balanced, strong and secure connections.
|
Pre-applied thread sealant for airtight connections. Simplifies field installation by eliminating the need for thread sealant tape. Plated steel construction with drag guard for jobsite durability and reliability. 6-ball coupler design for balanced, strong and secure connections.
|
Intended for compressed air lines only. 300 PSI maximum rated working pressure. Includes one each: No.12-425 1/4" Male NPT Plug. Most easily recognized design. Distinctive, long 3/4" pilot can not be confused with any other designs. No.13-435 1/4" Female Coupler - Due to their large size, do not connect or disconnect if the line pressure exceeds 40 PSI.
|
|
|
|
|
|
|
|
|
|
|
|
|
Comfortable thumb lever valve control with handy hanger in lever and hanger hook. Compact one piece nozzle. Allows full line pressure to be used. Includes 1/4" female NPT inlet. To comply with OSHA regulations standard blowguns must be used on a regulated air line with a pressure setting not to exceed 30 PSI.
|
Interchangeable nozzles for cleaning and inflating. Complies with OSHA regulations standard blowguns must be used on a regulated air line with a pressure setting not to exceed 30 PSI. Includes: standard nozzle, tapered inflator nozzle and ball inflator nozzle.
|
Utilizes the tubular valve which supports the seal and allows more air flow at lower pressure drops than most competitive couplers. Protective collar guards against accidental disconnect. Due to their large size, do not connect or disconnect if the line pressure exceeds 40 PSI. Intended for compressed air lines only. 300 PSI maximum rated working pressure.
|
|
|
|
|
|
|
|
|
|
|
|
|
Combination of a blowgun and the siphon spray nozzle. Barbed siphon inlet fits 1/4 inch ID hose or tubing. Use for spray- cleaning engines, applying protective coating, etc. Allows full line pressure to be used. Includes 1/4" female NPT inlet. To comply with OSHA regulations standard blowguns must be used on a regulated air line with a pressure setting not to exceed 30 PSI.
|
High speed steel.
|
Dependable male steel mechanical fitting is perfect for rapidly and securely separating air hoses.
|
|
|
|
|
|
|
|
|
|
|
|
|
Siphon feed type. Required pressure of 50-75 psi. Minimum 3.8" hose diameter.
|
Quadraport can operate at two different PSI settings at the same time for a wider variety of applications with 4 universal push-to-connect couplers for ease of operation. Liquid-filled gauge for durability and more accurate reading closer to job site. High flow regulator for increased performance, 3/8" diameter inlet fitting allows higher air flow and reduces PSI drop when used with 1/2" dia. hose. Robust carry handle for added protection and hang holes for convenient, secure remote positioning. Tool weight is 4 lbs.
|
Brass.
|
|
|
|
|
|
|
|
|
|
|
|
|
Mintcraft Air Hose End, 1/4 in Nominal, MNPT End, 3/8 in Inside Diameter
|
Mintcraft Hose Plug, 1/4 in Nominal, MNPT End, Brass
|
Brass.
|
|
|
|
|
|
|
|
|
|
|
|
|
All brass.
|
All brass.
|
All brass.
|
|
|
|
|
|
|
|
|
The FlexVolt 60 volt max 2.5 gallon cordless air compressor offers all of the convenience and portability of cordless with the power of a corded tool. Each battery charge allows for up to 1,220 nails, providing the run-time to complete a variety of applications. OneTurn regulator for fast, accurate pressure adjustments. Heavy duty roll cage for jobsite applications. Brushless motor paired with a heavy duty oil-free pump. 135 max psi tank storage. Lightweight and portable at only 21.5 lbs. and a height of 15.5". Made in the USA.
|
|