Home > ELECTRICAL > ROUGH ELECTRICAL > PANEL BOXES
Sort By:
1 2
GROUND BAR 7 HOLE CONSUMER PK Cutler Hammer BRFPP Filler Plate GE THFILLER Rectangle Filler Plate
For grounding copper or aluminum terminals in a GE load center. Offers 4 small holes for 14 - 8 AWG copper or 12 - 8 AWG aluminum terminals and 3 large holes for 14 - 4 AWG copper or 12 - 4 AWG aluminum terminals. UL Listed and ANSI Certified. 6.875" height x 2.875" width x 0.5" depth, .105 lb. Plastic (snap-in) for type BR 1" space. May also be used with 400 amp and 600 amp load centers. Covers circuit breaker knock outs that have been removed in error.  Two 1" and two 1/2" plates.
LUG KIT NO6-2/0 NEUTRAL/GROUND Square D QO70AN Auxiliary Neutral Lug Kit Schneider PK3GTA-1CP Ground Bar Kit
For use with wire range 6-2/0. Can be mounted on any neutral or ground position by simply removing the termination screw. UL Listed. 2.875" height x .75" width x  6.875" depth, .07 lb. Made for QO load centers. Field installed for number 12 - 2 Al or number 14 - 4 Cu wire. QO accessories can only be used with QO load centers. Used in load centers, CSED devices and NQOD and NF panel boards. Each terminal accepts (1) #14 - #4 copper wire or (1) #12 - #4 aluminum wire, (2) #14 - #12 copper wire or (2) #12 - #10 aluminum wire. NOTE - Consult local code for correct application of ground bar kit for service entrance equipment. ANSI Certified and UL Listed.
Square D QOFPCP Filler Plate GROUND BAR 24 HOLE PM-GOLD PK Square D HOM100AN Neutral Lug Kit
Fills opening in covers if twistout is removed in error. QOFPCP are used only in QO load centers, filling the spaces where no circuit is attached. CHOMFPCP are for use only in Homeline load centers. UL Listed and ANSI Certified. Used for additional grounding as required by local code. Compatible with most load center enclosures. Fits solid or stranded 4 - 14 copper wire and 10 - 12 aluminum wire. Includes mounting screws. UL Listed and ANSI Certified. 11" height x 3.5" width x 0.5" depth, .304 lb. Breaker box neutral lug is designed for Homeline load centers. It works with number 1 - 1/0 copper and aluminum wire. UL Listed, ANSI Certified.
Square D HOMFPCP Filler Plate Siemens EC38595 Closure Plate GE Electrical TFN60RCP AC Disconnect Switches
Fills opening in covers if twistout is removed in error. QOFPCP are used only in QO load centers, filling the spaces where no circuit is attached. CHOMFPCP are for use only in Homeline load centers. UL Listed and ANSI Certified. Fits any meter socket application where a closure plate is needed. Steel enclosure. 2 pole, 3 wire, 240 volt AC, rated 10 HP. For central air conditioner. Removable closing cap not included. Equipment ground. 14 - 3 AWG lug wire range. 4-3/4" x 7-1/2" x 2". UL1429 enclosure pullout switch, UL Listed.
Eaton DPU222RP Type ACD Non-Fusible Pullout Disconnect Switch Siemens Energy WN2060U AC Disconnect Switches Cutler-Hammer DPF221RP AC Disconnect Switches
Single phase, 2 pole, 2 wire, 240 volt AC, galvanized steel enclosure with molded case switch. Rated 3 HP at 120 volt, 10 HP at 240 volt. For bottom entry and exit only. Heavy duty, high strength enclosure with welded and riveted construction. Swing-up cover remains in place when in open position, and includes provision for padlocking. 10,000 AIR. When pullout is in off position, protective shield can be removed for access to fuses. No.GB4 ground bar and No.96-3258-4 pullout head replacement sold separately. #14-3 AWG wire range. 5-3/8" x 8-3/4" x 3-1/8". UL Listed file No.E5239. Single phase, 2 pole, 2 wire, 240 volt, rated 10 HP, steel enclosure. All lugs positioned for bottom entry and exit wiring. Easy mounting for quick installation. Pullout head can be replaced in off position. 10,000 AIR. 12 - 3 AWG al, 14 - 3 kcmil cu lug wire range. 5-5/32" x 7-5/16" x 2-7/32". UL Listed. Air conditioning disconnect, pullout, fused, 2-pole, 120/240 volt AC. Wire size range of  #14-3 Cu or Al at 60 or 70 degrees C. Metallic color galvanized steel enclosure, 9" x 5.5" x 3". NEMA 3R, rainproof. UL Listed, CSA Approved.
GE Electrical TPN60R1 AC Disconnect Switches Square D QO2L30SC Load Center PowerMark Gold TL412C Standard Load Center
Suitable for use as service entrance equipment. Removable closing cap not included. Equipment ground. 14 - 3 AWG lug wire range. Designed to comply with code requirements for disconnecting central air conditioners and heat pumps. Open sides and top for quick installation. Impact and corrosion resistant GE Noryl thermoplastic resin. 2 pole, 3 wire, 120/240 volt AC, rated 10 HP. 5-3/4" x 8" x 3-1/8". UL1429 enclosed pullout switch, UL Listed. Main lug load center, indoor, 30 amp, 2 spaces/2 circuits. Accommodates both overhead and underground feed applications. 1" maximum knockout on the top and bottom of the enclosure. Comes with a doorless surface mount cover and factory installed main lugs. UL Listed. Single-phase, three-wire, 120/240 volt AC. (4) 1" circuits or (8) 1/2" circuits. One-piece interior removes and reinstalls easily. Full-length neutrals are easier to wire, reducing installation time and cost. Minimum 100 percent neutral terminations. Sturdy copper bus and galvanized box increase durability and reliability. Combination slotted/Robertson screws speed wiring. All holes are rated for 14-4 wire. 100 per cent rated split neutral on each side. Load centers accept Q Line circuit breakers, including GE's exclusive 1/2" THQPs. 10,000 AIC. 40 - 225 amp single phase devices have removable closing caps. TL load center enclosures are galvanized steel. 7-1/4" x 9" x 3". UL Listed.
Cutler-Hammer AC222URNMP-A2 AC Disconnect Switches Homeline Square D HOM24L70S Load Center Square D S106 Replacement Screw
Single phase, 2 pole, 2 wire, 240 volt AC. Rated 3 HP at 120 volt, 10 HP at 240 volt. For top and bottom entry and exit, with provision for type H conduit hub. Heavy duty, high strength, rugged polymer enclosure with UV resistant features. Swing-up cover remains in place when in open position, protective shield can be removed for access to fuses. No.GB4 ground bar and No.360-011-24 pullout head replacement sold separately. #14-2 AWG wire range. 5" x 8-5/8" x 3-1/2". UL Listed file No. E5239. Main lug indoor load center, 70 amp, 2 spaces/4 circuits. Maximum SCCR of 10,000 and a maximum load of 240 volts. NEMA type 1 enclosure. Expandable loadcentre capacity with the use of tandem or quad breakers. CSA approved for vertical, horizontal or inverted mounting. Accepts aluminum or copper conductors. Approved to only accept Canadian HomeLine breakers. Fit many types of service entrance devices and load center covers. Use them to replace lost or damaged screws.
GE Electrical TF60RCP AC Disconnect Switches Square D L211N Safety Switches Homeline Square D HOM24L70F Load Center
Steel enclosure. 2 pole, 3 wire, 120/240 volt AC, rated 10 HP. Uses cartridge fuses. For central air conditioner. Designed to comply with code requirements for disconnecting means within sight of central air conditioners and heat pumps. Removable closing cap not included. Equipment ground. 14-3 AWG lug wire range. 6-1/2" x 9" x 3-1/4". UL869 service equipment, UL Listed. Single phase, 2 pole, 3 wire, solid neutral, 120/240 volt AC. Rated 3 HP at 240 volt AC, with metallic enclosure. Typical uses include workshop or hobby room, water heater, furnace, garage or well pump disconnect. 10,000 AIC (short circuit rating) with plug fuses. Padlock attachment for lock off. 5.00" x 7.63" x 4.00". UL Listed, meets NEMA standard KS1. Main lug indoor load center, 70 amp, 2 spaces/4-circuits. NEMA type 1 enclosure with a flush mount cover. Overhead or underground feeds with 1-1/4" knockouts in both the top and bottom endwalls. Compatible with Homeline 1 pole and tandem breakers and a PK3GTA1 ground bar kit (not included). UL Listed.
Eaton BR24L70SP Load Center Eaton BR24L70FP Load Center Cutler Hammer BRL200 Main Lug Kit
Steel enclosure. Single phase, 3 wire, insulated/bondable movable neutral, 2 (1") spaces, 4 poles, 120/240 volt. No.GBK5 or GBK520 ground bars and doors sold separately. Tin-plated aluminum bus bar. In accordance with NEC, suitable for use as service equipment when not more than 2 service disconnecting mains are provided or when not used as lighting and appliance panelboard. When bonded, unused neutral connections may be used for equipment ground protectors in service entrance application. #8 - #2 wire range. Electrostatic powder coat, baked urethane painted. Rotate 180 degrees for bottom feed. Style 5 box 4-1/2" x 9-7/16" x 3". UL Listed file E8741. Single phase, 3 wire, insulated/bondable neutral, 2 (1") spaces, 4 poles, 120/240 volt AC. No. GBK5 or No. GBK520 ground bars and doors sold separately. Tin-plated aluminum bus bar. In accordance with NEC, suitable for use as service equipment when not more than 2 service disconnecting mains are provided or when not used as a lighting and appliance panelboard. Neutral is movable to other side. When bonded, unused neutral connections may be used for equipment ground protectors in service entrance application. #8 - #2 wire range. Electrostatic powder coat, baked urethane painted. Rotate 180 degrees for bottom feed. Style 5 box 4-1/2" x 9-7/16" x 3". UL Listed file E8741. Two pole - 200 amp - pair.
Square D QO200TRCP Molded Non-Fusible Disconnect Switch Square D L111N Fusible Light Duty Safety Switch Cutler-Hammer DPF222RP AC Disconnect Switches
For use with 75 degree Celsius wire. 2 pole, 2 wire, 240 volt AC, rated 10 HP, steel enclosure with molded case. With reliable, quick-make, quick-break operating mechanism. Suitable for use on systems with up to 10,000 RMS symmetrical amp available fault current at 240 volt AC maximum when protected by a fuse or circuit breaker rated 60 amp or less. Does not contain overcurrent protection. Ground bar bonded to back. 4-5/8" x 6-1/2" x 3-7/8". UL Listed. Single phase, 1 pole, 2 wire, solid neutral, 120/240 volt AC. Rated 2 HP at 120 volt AC, with metallic enclosure. Typical loads include workshop or hobby room, water heater, furnace, garage or well pump disconnect. 10,000 AIC (short circuit rating) with plug fuses. Padlock attachment for lock off. UL Listed, meets NEMA standard KS1. 5.00" x 7.63" x 4.00". Air conditioning disconnect, pullout, fused, 2-pole, 120/240 volt AC. Wire size range of  #14-3 Cu or Al at 60 or 70 degrees C. Metallic color galvanized steel enclosure, 9" x 5.5" x 3". NEMA 3R, rainproof. UL Listed, CSA Approved.
Square D QO24L70S Load Center Murray LC004NSU Load Center Homeline Square D HOM612L100S Load Center
Main lug load center, intended for fixed applications. 70 amp, 2 spaces/4 circuits. Surface mount cover with door and a NEMA type 1 enclosure for indoor use. Single phase unit, features a copper bus for conductivity and is rated for up to 10,000 SCCR. ANSI Certified and UL Listed. Single phase - 3 wire; 120/240 volt;  8 circuits maximum with 4 - 1" spaces. 14" length x 8-1/2" width x 3-1/4" depth. 10,000 AIC. UL listed. Main lug indoor load center, 100 amp,  6 space/12 circuit. NEMA type 1 enclosure.  Single phase, 3 wire, solid neutral. Expandable loadcentre capacity with the use of tandem or quad breakers. CSA approved for vertical, horizontal or inverted mounting. Accepts aluminum or copper conductors. Approved to only accept Canadian HomeLine breakers.
PowerMark Gold TLM612FCUD Standard Convertible Load Center Homeline Square D HOM612L100F Load Center Eaton BR48L125FP Load Center
Indoor flush or surface mount with door. Box is significantly smaller and lighter while maintaining optimum wire-bending space. Side mounted main  breaker allows top or bottom feed. Sturdy copper bus and galvanized box increase durability and reliability; tinplated for corrosion resistance. Minimum 100 per cent neutral terminations. All neutral holes rated for 14-4 wire. Extruded neutrals are easier to wire, reducing installation time and cost. Combination slotted/Robertson screws speed wiring. Accepts GE Q-Line branch circuit breakers, including GE's exclusive 1/2" THQPs. Interior removes and reinstalls easily. Main breaker not included. (6)  1" circuits or (12)  1/2"  circuits. 12-5/8" x 12-3/8" x 3-3/8". UL Listed. Main lug indoor load center, 100 amp, 6 space/12 circuit. 1-1/2" knockouts in the top and bottom end walls to allow for use with either overhead or underground fed electrical wiring. 22,000 short circuit current rating (SCCR) and can be fitted with a secondary surge arrestor (not included) for added protection. Single phase, 3 wire, solid neutral. UL Listed. Steel enclosure. Single phase, 3 wire, insulated/bondable neutral, 4 (1") spaces, 8 poles, 120/240 volt. No.GBK10 ground bars and doors sold separately. Tin-plated aluminum bus bar. In accordance with NEC, suitable for use as service equipment when not more than 2 service disconnecting mains are provided or when not more than 6 service disconnecting mains are provided and when not used as a lighting and appliance panelboard. Neutral is movable to other side. When bonded, unused neutral connections may be used for equipment ground protectors in service application. #14 - 1/0 AWG wire range. Electrostatic powder coat, baked urethane painted. Rotate 180 degrees for bottom feed. Style 7 box - 11" x 13" x 3-9/16". UL Listed file E8741.
Eaton BR48L125SP Load Center Cutler-Hammer DP221NGB Safety Switches Eaton BR24L70RP Load Center
Steel enclosure. Single phase, 3 wire, insulated/bondable neutral, 4 (1") spaces, 8 poles, 120/240 volt. No. GBK10 ground bars and doors sold separately. Tin-plated aluminum bus bar. In accordance with NEC, suitable for use as service equipment when not more than 2 service disconnecting mains are provided or when not more than 6 service disconnecting mains are provided and when not used as a lighting and appliance panelboard. Neutral is movable to other side. When bonded, unused neutral connections may be used for equipment ground protectors in service application. #14 - 1/0 AWG wire range. Electrostatic powder coat, baked urethane painted. Rotate 180 degrees for bottom feed. Style 7 box - 11" x 13" x 3-9/16". UL Listed file E8741. Steel enclosure. 2 pole, 3 wire, general duty safety switch, plug fuse type, (Type S, T, OR W) fusible with neutral NEMA 1. 120/240 volt rating. 1/2 HP at 120 volt, 1-1/2 HP at 240 volt. Does not have an interlock to prevent opening when switch is in the on position. UL Listed. Rainproof galvanized steel enclosure. Single phase, 3 wire, insulated/bondable movable neutral, 2 (1") spaces, 4 poles, 120/240 volt AC. With closure plates, hubs and No.GBK5 or GBK520 ground bar kits (necessary for sub-feeding) sold separately. Tin-plated aluminum bus bar. In accordance with NEC, suitable for use as service equipment when not more than 2 service disconnecting mains are provided or when not used as a lighting and appliance panelboard. When bonded, unused neutral connections may be used for equipment ground protectors in service entrance application. #8 - #2 wire range. Electrostatic powder coat, baked urethane painted. 4-1/2" x 9-7/16" x 3". UL Listed file E8741. Style 5R box.
Cutler-Hammer ACD221RNMP AC Disconnect Switches Siemens E0204ML1060SU Load Center Eaton BR612L125FDP Load Center
Single phase, 2 pole, 2 wire, 240 volt AC, non-metallic enclosure. Rated 1-1/2 HP at 120 volt, 3 HP at 240 volt with time delay fuses (uses class H cartridge fuses, not included). For top and bottom entry and exit, with provision for type H conduit hub. Heavy duty, high strength, rugged polymer enclosure with UV resistant features. 10,000 amp RMS symmetrical interrupting rating. Suitable for use as service entrance equipment with ground bar. No.GB4 ground bar and No.360-011-24 pullout head replacement sold separately. #14-2 AWG wire range. 5" x 8.63" x 3.5". UL Listed file No. E5239. Single phase, 3 wire, solid neutral, 2 spaces and 4 circuits maximum 1-pole, 1 QP breaker maximum 2-pole, 120/240 volt AC. 10,000 AIR. One piece plated aluminum bus bar, heavier main bus for cooler operation, direct cable connection to bus bar. Main lugs and neutral on same plane, same drive tool. 100 percent circuit breaker twistouts. Positive load side circuit breaker hook rail. When used as service equipment, any unused neutral position may be used for equipment grounding. Simple upper pan adjustment after trim is installed for flush leveling. Rotate entire device 180 degrees for bottom feed. Gray enamel finish. UL Listed, complies fully with NEC and UL requirements for Class CTL. 5-1/8" x 9-7/8" x 2-5/8". Steel enclosure. Single phase, 3 wire, insulated/bondable neutral, 6 (1") spaces, 12 poles, 120/240 volt. Furnished with door; No. GBK10 ground bar sold separately. Tin-plated aluminum bus bar. In accordance with NEC, suitable for use as service equipment when not more than 6 service disconnecting mains are provided and when not used as a lighting and appliance panelboard. Neutral is movable to other side. When bonded, unused neutral connections may be used for equipment ground protectors in service entrance application. Number 14 - number 1 AWG wire range. Electrostatic powder coat, baked urethane painted. Rotate 180 degrees for bottom feed. Style 7 box - 11" x 13" x 3-9/16". UL Listed file E8741.
Siemens E0408ML1125SU Load Center Square D QO612L100FCP Load Center Square D QO612L100SCP Load Center
Code-gauge steel enclosure. Single phase, 3 wire, solid neutral, 4 spaces and 8 circuits maximum 1-pole, 2 QP breakers maximum 2-pole, 120/240 volt. 10,000 AIR. One piece plated aluminum bus bar. 100 percent circuit breaker twistouts. Positive load side circuit breaker hook rail. Suitable for use as service equipment when a main breaker (100 amp maximum) is back-fed in a branch position and used with main breaker retainer clip No.MBR1. When used as service equipment, any unused neutral position may be used for equipment grounding. Rotate entire device 180 degrees for bottom feed. Gray enamel finish. 6-5/8" x 12-5/8" x 3-1/2". UL Listed, complies fully with NEC and UL requirements for Class CTL. Main lug indoor load center, 100 amp, 6 space/12 circuit, intended for use in fixed applications. NEMA type 1 enclosure and a copper bus bar for conductivity. Single-phase, rated for up to 240 volts and has a 10,000 maximum SCCR. UL Listed. Main lug indoor load center, 100 amp, 6 spaces/12 circuits. 1-1/2" maximum knockouts in the top and bottom end walls for overhead or underground feed. NEMA type 1 for indoor use. Steel enclosure. Single phase, solid neutral. UL Listed.
Homeline Square D HOM24L70RB Load Center Square D L221N Safety Switches Eaton BR816L125FP Load Center
Main lug outdoor load center, 70 amp, 2 space and 4 circuit. NEMA type-3R enclosure with a rainproof cover for outdoor use. Class 1170 unit is intended for use in fixed applications and can accommodate overhead or underground feed. Maximum SCCR of 10,000. ANSI Certified and UL Listed. Single phase, 2 pole, 3 wire (2 blades, fuseholders and 1 neutral), 120/240 volt AC. Rated 3 HP at 240 volt AC, with metallic enclosure. 10,000 AIC (short circuit rating) with class H cartridge fuses. NEMA type 1 enclosure. Terminal lug data: (1) #12 - 6 Al or #14 - 6 Cu. wire. Service ground bar kit PKGTA1 sold separately. Padlock attachment for lock off. UL Listed, meets NEMA standard KS1. Steel enclosure. Single phase, 3 wire, insulated/bondable neutral, 8 (1") spaces, 16 poles, 120/240 volt. No.GBK10 ground bar and door sold separately. Tin-plated aluminum bus bar. In accordance with NEC, suitable for use as service equipment when a main breaker is used or when not more than 6 service disconnecting mains are provided and when not used as a lighting and appliance panelboard. Neutral is movable to other side. When bonded, unused neutral connections may be used for equipment ground protectors in service entrance application. #14 - #1 AWG wire range. Electrostatic powder coat, baked urethane painted. Rotate 180 degrees for bottom feed. Style 7 box - 11" x 13" x 3-9/16". UL Listed file E8741.
Square D D211NCP Safety Switches PowerMark Gold TL240RCU Standard Load Center PowerMark Gold TL270RCUP Standard Load Center
Single phase, 2 pole, 3 wire, 2 blades and fuseholders, factory installed solid neutral, 120/240 volt AC. With metallic enclosure for indoor use. Designed to open or close an electrical circuit in general duty applications. Rated 1-1/2 HP. For residential or commercial applications. For PK3GTA-1 field installable service ground bar kit. With plug type fuse protection. Lugs suitable for aluminum or copper conductors. Spring reinforced plated copper fuse clips. ANSI Certified and UL Listed. Single-phase, three-wire, 120/240 volt AC. One-piece interior removes and reinstalls easily. Full-length neutrals are easier to wire, reducing installation time and cost. 100 percent neutral terminations. Sturdy copper bus and galvanized box increase durability and reliability. Combination slotted/Robertson screws speed wiring. All holes are rated for 14-4 wire. 100 per cent rated split neutral on each side. Load centers accept Q Line circuit breakers, including GE 1/2" THQP. (2) 1" or (4) 1/2"  spaces; 22,000 AIC. 7-1/4" x 10" x 3-31/4". One-piece interior removes and reinstalls easily. Full-length neutrals are easier to wire, reducing installation time and cost. Minimum 100 percent neutral terminations. Sturdy copper bus and galvanized box increase durability and reliability. Combination slotted/Robertson screws speed wiring. All holes are rated for 14-4 wire. 100-percent rated split neutral on each side. Load centers accept Q Line circuit breakers, including GE's exclusive 1/2"  THQPs. (2) 1" or (4 )1/2" spaces; 22,000 AIC. Single-phase, three-wire, 120/240 Volt AC. 7-1/4" x 10" x 3-3/4".
Murray LW002GRU Load Center Eaton BR612L125RP Load Center Eaton BR816L125SDP Load Center
Single phase - 3 wire; 120/240 volt;  4 circuits maximum;  2 - 1" spaces ; 10,000 AIC. 9-1/4" x 6-5/8" x 3-3/8". UL Listed. Rainproof galvanized steel enclosure. Single phase, 3 wire, insulated/bondable movable neutral, 6 (1") spaces, 12 poles, 120/240 volt AC. With closure plates, hubs and No.GBK10 ground bar kits (necessary for sub-feeding) sold separately. Tin-plated aluminum bus bar. In accordance with NEC, suitable for use as service equipment when a main breaker is used or when not more than 6 service disconnecting mains are provided and when not used as a lighting and appliance panelboard. When bonded, unused neutral connections may be used for equipment ground protectors in service entrance application. #14-#1 wire range. Electrostatic powder coat, baked urethane painted. Style 7R box 11" x 13" x 3-9/16". UL Listed file E8741. Steel enclosure. Single phase, 3 wire, insulated/bondable neutral, 8 (1") spaces, 16 poles, 120/240 volt. Furnished with door. Ground bar No.GBK10 sold separately. Tin-plated aluminum bus bar. In accordance with NEC, suitable for use as service equipment when a main breaker is used or when not more than 6 service disconnecting mains are provided and when not used as a lighting or appliance panelboard. Neutral is movable to other side. When bonded, unused neutral connections may be used for equipment ground protectors in service entrance application. #14-#1 wire range. Electrostatic powder coat, baked urethane painted. Rotate 180 degrees for bottom feed. Style 7 box - 11" x 13" x 3-9/16". UL Listed file E8741.
PowerMark TPL412RP Standard Load Center Eaton BR48L125RP Load Center Siemens Energy LF211NU Safety Switches
One-piece interior removes and reinstalls easily. Full-length neutrals are easier to wire, reducing installation time and cost. Minimum 100 percent neutral terminations. Sturdy copper bus and galvanized box increase durability and reliability. Combination slotted/Robertson screws speed wiring. All holes are rated for 14-4 wire. 100 per cent rated split neutral on each side. Load centers accept Q Line circuit breakers, including GE's exclusive 1/2"  THQPs. (4) 1" or (8)  1/2"  spaces; 10kAIC. Single-phase, Three-wire, 120/240 volt AC. 7-1/2" x 9-7/32" x 3-5/16". Rainproof galvanized steel enclosure. Single phase, 3 wire, insulated/bondable movable neutral, 4 (1") spaces, 8 poles, 120/240  volt AC. With closure plates, hubs, and No.GBK10 ground bar kits (necessary for sub-feeding) sold separately. Tin-plated aluminum bus bar. In accordance with NEC, suitable for use as service equipment when not more than 2 service disconnecting mains are provided or when not more than 6 service disconnecting mains are provided and when not used as a lighting and appliance panelboard. When bonded, unused neutral connections may be used for equipment ground protectors in service entrance application. #14-1/0 wire range. Electrostatic powder coat, baked urethane painted. Style 7R box 11" x 13" x 3-9/16". UL Listed file E8741. Single phase, 2 pole, 3 wire, solid neutral, 120/240 volt. 10,000 AIC with plug fuses (not included). Metallic enclosure. Rated 1-1/2 HP standard/3 HP maximum. Compact size, quick-make, quick-break mechanism. Suitable for use as service entrance equipment. Cover interlock. Bottom cable entry and exit only, no hub provision supplied. Padlocking provision to lock cover closed or to lock in off position. Lugs suitable for copper or aluminum. Silver plated copper conductors. #14-6 AWG line, #14-8 load lug wire ranges. 5-1/2" x 8-1/4" x 5-13/16". UL Listed file No.E4776, NEMA type GD, meets federal specifications WS865C.
PowerMark Gold TLM812FCUD Standard Convertible Load Center Eaton BR24L125RP Enclosed Load Center Murray LW004NRU Load Center
Box is significantly smaller and lighter while maintaining optimum wire-bending space. Side mounted main breaker allows top or bottom feed. Sturdy copper bus and galvanized box increase durability and reliability; tinplated for corrosion resistance. Minimum 100 per cent neutral terminations. All neutral holes rated for 14-4 wire. Extruded neutrals are easier to wire, reducing installation time and cost. Combination slotted/Robertson screws speed wiring. Accepts GE Q-Line branch circuit breakers, including GE's exclusive 1/2" THQPs. Interior removes and reinstalls easily. Main breaker not included. (8) 1" circuits or (16) 1/2" circuits. 12-5/8" x 12-3/8" 3-3/8". UL Listed. Rainproof galvanized steel enclosure. Single phase, 3 wire, insulated/bondable movable neutral, 2 (1") spaces, 4 poles, 120/240 volt AC. With closure plates, hubs and No.GBK5 or GBK520 ground bar kits (necessary for sub-feeding) sold separately. Tin-plated aluminum bus bar. In accordance with NEC, suitable for use as service equipment when not more than 2 service disconnecting mains are provided or when not used as a lighting and appliance panelboard. When bonded, unused neutral connections may be used for equipment ground protectors in service entrance application. #14-1/0 wire range. Electrostatic powder coat, baked urethane painted. Style 6R box 6-7/8" x 12" x 4-1/2". UL Listed file E8741. Convertible to main breaker using double pole breaker. 2 full spaces. 4 space, 8 circuit, combination mount.
Cutler-Hammer DG221NGB Safety Switches Eaton BR612L125SP Load Center Siemens EQ W0204ML1060U Load Center
Steel enclosure. 2 pole, 3 wire, 2 blades, 2 class H cartridge fuses (not included), solid neutral, 120/240 volt AC. Rated 1-1/2 to 3 HP single phase, 3 to 7-1/2 HP 3-phase at 240 volt only when dual element fuses are used. For residential and commercial applications. Suitable for light duty motor circuits and service entrance. For use on systems capable of delivering up to 10,000 RMS, symmetrical fault current. Bolt on hub provided. DS100GK ground kit sold separately. 6-1/6" x 7-1/2" x 6-3/4". UL Listed file No.E5239; meets UL98 for enclosed switches and NEMA standard KS1. Steel enclosure. Single phase, 3 wire, insulated/bondable neutral, 6 (1") spaces, 12 poles, 120/240 volt. No.GBK10 ground bar and door sold separately. Tin-plated aluminum bus bar. In accordance with NEC, suitable for use as service equipment when a main breaker is used or when not more than 6 service disconnecting mains are provided and when not used as a lighting and appliance panelboard. Neutral is movable to other side. When bonded, unused neutral connections may be used for equipment ground protectors in service entrance appliance. #14 - #1 wire range. Electrostatic powder coat, baked urethane painted. Rotate 180 degrees for bottom feed. Style 7 box - 11" x 13" x 3-9/16". UL Listed file E8741. Single phase, 3 wire, solid neutral, 2 spaces and 4 circuits maximum 1-pole, 1 QP breaker maximum 2-pole, 120/240 volt AC. 10,000 AIR. With closure plates, HS style hubs sold separately, uses ECHA075 (694.3559) Hub. One piece plated aluminum bus bar. 100 percent circuit breaker twistouts. Will not accommodate 2-pole GFCI or circuit breaker with shunt trip. Positive load side circuit breaker hook rail. When used as service equipment, any unused neutral position may be used for equipment grounding. Rotate entire device 180 degrees for bottom feed. Gray enamel finish. CSA and UL Listed, complies fully with NEC and UL requirements for Class CTL. 5" x 8" x 4-1/4".
LOAD CENTR 125A 8SP 16C INDOOR Siemens EQ W0408ML1125U Load Center Murray LC008DSU Load Center
Value kit, indoor. Includes a sturdy highly-conductive tin-plated copper buss bar and a rust-resistant galvanized box. Indoor NEMA 1 enclosure with combination surface/flush front. Factory-installed main lug, full-length neutral bars, top or bottom feed and self-adjusting, dead-front cover. One-piece interior removes and re-installs easily. Single-phase, 3-wire, 120/240-volt and 22K AIC rating. All holes are rated for 14-4 wire and 100 percent rated split neutrals on each side. Accepts Q-Line THQL standard, GFCI and AFCI circuit breakers, including GE's exclusive 1/2" THQPs. UL Listed and ANSI Certified. 16" height x 14" width x 3.375" depth, 16.79 lb. Code-gauge steel enclosure. Single phase, 3 wire, solid neutral, 4 spaces/8 circuits 1-pole, 2 QP breakers 2-pole, 120/240 volt AC. 10,000 AIR. With closure plates, HS-hubs sold separately. One piece plated aluminum bus bar. 100 percent circuit breaker twistouts. Positive load side circuit breaker hook rail. Suitable for use as service equipment when a main breaker (100 amp maximum) is back-fed in a branch position and used with main breaker retainer clip No.MBR1. When used as service equipment, any unused neutral position may be used for equipment grounding. Rotate entire device 180 degrees for bottom feed. Gray enamel finish. CSA and UL Listed, complies fully with NEC and UL requirements for Class CTL. 6" x 12-1/4" x 4-1/4". Single phase type 1 with 8-1" spaces, 16 circuits. Use neutral lug kit DLK1 or DLK2 as required. Indoor closure with door.
GE TL412R1P Standard Load Center Homeline Square D HOM612L100RB Load Center Eaton CH2L70RP Load Center
One-piece interior removes and reinstalls easily. Full-length neutrals are easier to wire, reducing installation time and cost. 100 percent neutral terminations. Sturdy copper bus and galvanized box increase durability and reliability. Combination slotted/Robertson screws speed wiring. All holes are rated for 14-4 wire. 100 per cent rated split neutral on each side. Load centers accept Q Line circuit breakers, including GE's exclusive 1/2" THQPs. (4) 1" or (8) 1/2"  spaces. Single-phase, three-wire, 120/240 Volt AC. 7-1/4" x 10" x 3-3/4". Outdoor main lug load center, 100 amp, 6 space and 12 circuits. Can be wired for underground or overhead feeds with a 2-1/2" hub on the top and a 1-1/2" knockout on the bottom. NEMA type 3R enclosure resists rain for durable performance. ANSI Certified and UL Listed. Rainproof galvanized steel enclosure. Single phase, 3 wire, insulated/bondable neutral, 2 (3/4") spaces, 4 poles with CHNT breakers, 120/240 volt AC. With closure plates, hubs and ground bar No.GBK5 or No.GBK520 sold separately. Copper bus bar. In service entrance application, where neutral is bonded, unused neutral connections may be used for termination of equipment grounds. In accordance with NEC, suitable for use as service equipment when not more than 2 service disconnecting mains are provided or when not used as a lighting and appliance panelboard. #14 - 2 main lug wire range. Electrostatic powder coated. Style 5R box 4-1/2" x 9-1/2" x 3-1/8". UL Listed file E8741.
PowerMark Gold TLM1212CCU Standard Convertible Load Center Square D QO24L70RB Load Center Siemens SUAT111-0G General Duty Ringless Meter Socket
Box is significantly smaller and lighter while maintaining optimum wire-bending space. Side mounted main  breaker allows top or bottom feed. Sturdy copper bus and galvanized box increase durability and reliability; tinplated for corrosion resistance. Minimum 100 per cent neutral terminations. All neutral holes rated for 14-4 wire. Extruded neutrals are easier to wire, reducing installation time and cost. Combination slotted/Robertson screws speed wiring. Accepts GE Q-Line branch circuit breakers, including GE's exclusive 1/2" THQPs. Interior removes and reinstalls easily. Main breaker not included. 14 spaces, 24 circuits. 14-1/8" x 16-1/8" x 3-3/8". UL Listed. Main lug indoor load center, 70 amp, 2 spaces/4 circuits. Intended for overhead or underground feed. 1-1/4" maximum knockouts in the top and bottom end walls. NEMA 3R enclosure for outdoor use with a factory included cover. Copper bus for conductivity. UL Listed. Single phase, 3 wire, 4 jaw, 600 volt maximum. Jaws fabricated from high conductivity, tin plated copper alloy. Insulating jaw support blocks of high impact, non-tracking thermoset polyester. Galvanized steel enclosure. Safety guides reduce chances of accidental contact and aligns meter in sock. Uses RX style hub (not included). Provision for 5th jaw, no bypass. UL Listed.
Connecticut PS-13-HR Weatherproof Power Outlet Panel Connecticut PS-54-HR Weatherproof Power Outlet Panel Square D QO612L100RBCP Load Center
Factory wired and completely assembled. Suitable for use with aluminum or copper wire. Cover design allows cord to be used when door is closed. 30 amp, 120 volt. 6-1/8" x 5-3/8" x 4-3/4". TT-30R NEMA receptacle. NEMA 3R weatherproof enclosure. Safe and easy to install. Factory wired and completely assembled. Suitable for use with aluminum or copper wire. Unique cover design allows cord to be used when door is closed. 50 amp, 120/240 volt. 6-18" x 5-3/8" x 4-3/4". 14-50R NEMA receptacle. NEMA 3R weatherproof enclosure. Outdoor main lug load center, 100 amp, 6 space 12 circuit. NEMA type 3R enclosure with a rainproof cover. Copper bus bar, accommodates standard QO or QO tandem circuit breakers. ANSI Certified and UL Listed.
LOAD CENTER 125A 8SPACE 16CIR Siemens Energy SUAT111-OPQG Meter Sockets Siemens E0816ML1125S Load Center
Single-phase, Three-wire, 120/240 volt AC. Convertible. Full-length neutrals are easier to wire, reducing installation time and cost. Removable closing cap. Minimum 100 percent neutral terminations. Sturdy copper bus and galvanized box increase durability and reliability. Combination slotted/Robertson screws speed wiring. All holes are rated for 14-4 wire. 100 per cent rated split neutral on each side. Load centers accept Q Line circuit breakers, including GE's exclusive 1/2"  THQPs. UL listed. 11-1/4" x 11-1/8" x 3-1/4". Galvanized steel enclosure. Single phase, 3 wire, 4 jaw, 600 volt maximum. Jaws fabricated from high conductivity, tin plated, copper alloy. Insulating jaw support blocks of high impact, non-tracking thermoset polyester. Safety guides reduce chances of accidental contact, and aligns meter in sock. Uses RX style hub (not included). Includes two ground lugs. Swing switches are stainless steel. Provision for 5th jaw. UL Listed. Code-gauge steel enclosure. Single phase, 3 wire, solid neutral, 8 spaces and 16 circuits maximum 1-pole, 4 QP breakers maximum 2-pole, 120/240 volt. 10,000 AIR. One piece plated aluminum bus bar. 100 percent circuit breaker twistouts. Positive load side circuit breaker hook rail. Suitable for use as service entrance equipment when a main breaker (125 amp maximum) is back-fed in branch position and used with main breaker retainer clip No.MBR1. When used as service equipment, any unused neutral position may be used for equipment grounding. Rotate entire device 180 degrees for bottom feed. Gray enamel finish. 12-3/8" x 14-3/4" x 3-7/8". UL Listed, complies fully with NEC and UL requirements for Class CTL.
Siemens Energy SUAT417-XG Meter Sockets Square D QO816L100FCP Load Center Square D QO816L100SCP Load Center
Single phase, 3 wire, 4 jaw, 600 volt maximum. Jaws fabricated from high conductivity, tin plated, copper alloy. Insulating jaw support blocks of high impact, non-tracking thermoset polyester. Galvanized steel enclosure. Safety guides reduce chances of accidental contact, and aligns meter in sock. Uses RX style hub (not included). Provision for 5th jaw and closure plate included, no bypass. UL Listed. Main lug indoor load center, 100 amp, 8 space/16 circuit. 1-1/2" maximum knockouts in the top and bottom end walls to accommodate overhead or underground feed. The center is rated for a maximum load of 240 volts and has a 10,000 SCCR. NEMA type 1. Copper bus for conductivity. Single phase, 3 wire, solid neutral. UL Listed. Main lug indoor load center, 100 amp, 8 spaces/16 circuits. 1-1/2" maximum knockouts in the top and bottom end walls to accommodate overhead or underground feed. Maximum load of 240 volts and a 10,000 SCCR. NEMA type 1. Copper bus for conductivity. Single phase, 3 wire, solid neutral. UL Listed.
Siemens ES S1224L1125 Load Center Eaton BR816L125RP Load Center Siemens SUAT317-0G General Duty Ringless Meter Socket
Single phase, 3 wire, Rated 100,000A IR. Aluminum bus bar, tin plated. ANSI 61 gray powder coated. Suitable for use as service equipment when not more than six main disconnecting means are provided. 12 spaces, 24 circuits maximum. 18" height x 14-1/4" wide by 3-7/8" deep. Rainproof galvanized steel enclosure. Single phase, 3 wire, insulated/bondable movable neutral, 8 (1") spaces, 16 poles, 120/240 volt AC. With closure plates, hubs and No.GBK10 ground bar kits (necessary for sub-feeding) sold separately. Tin-plated aluminum bus bar. In accordance with NEC, suitable for use as service equipment when a main breaker is used or when not more than 6 service disconnecting mains are provided and when not used as a lighting and appliance panelboard. When bonded, unused neutral connections may be used for equipment ground protectors in service entrance application. #14-#1 wire range. Electrostatic powder coat, baked urethane painted. Style 7R box 11" x 13" x 3-9/16". UL Listed file E8741. Single phase, 3 wire, 4 jaw, 600 volt maximum. Jaws fabricated from high conductivity, tin plated copper alloy. Insulating jaw support blocks of high impact, non-tracking thermoset polyester. Galvanized steel enclosure. Safety guides reduce chances of accidental contact and aligns meter in sock. Uses RX style hub (not included). Provision for 5th jaw, no bypass. UL Listed.
Siemens Energy SUAT317-OPQG Meter Sockets Siemens SJ102AX Ring Meter Socket BRLC 125A 12/24CR AL BUS/WGB
Galvanized steel enclosure. Single phase, 3 wire, 4 jaw, 600 volt maximum. Jaws fabricated from high conductivity, tin plated, copper alloy. Insulating jaw support blocks of high impact, non-tracking thermoset polyester. Safety guides reduce chances of accidental contact, and aligns meter in sock. Uses RX style hub (not included). Includes two ground lugs. Swing switches are stainless steel. Provision for 5th jaw. UL Listed. Single phase, 3 wire, 4 jaw, 600 volt maximum 10,000 AIR. Jaws fabricated from high conductivity, tin plated, copper alloy. Insulating jaw support blocks of high impact, non-tracking thermoset polyester. Galvanized steel enclosure. Safety guides reduce chances of accidental contact, and aligns meter in sock. Uses RX style hub (not included). Provision for 5th jaw, no bypass. UL Listed. BR style 1-inch loadcenter, main lug, ground bar, includes BREQS125 hold-down screw, 125A, single-phase, 24-pole, 24 circuits, 12 spaces, 120/240V, #6-2/0 AWG Cu/Al at 60 or 75 degreesC wire, NEMA 1 enclosure, b1 box size. Ground bar, includes BREQS125 hold-down screw. 10 kAIC interrupt rating. Aluminum bus, combination mounting. 3.88 in x 14.31 in x 16.75 in. Suitable for use as service equipment when no more than 6 main disconnecting means are provided or when not used as lighting and appliance panelboard. Has notch for brhdk125 hold-down kit.
Siemens EQ W0816ML1125CU Load Center Reliance PB30 Manual Outdoor Power Inlet Box GE Electrical TG3221R Spec-Setter Safety Switches
Code-gauge steel enclosure. Single phase, 3 wire, solid neutral, 8 spaces/16 circuits 1-pole, 4 QP breakers 2-pole, 120/240 volt AC. 10,000 AIR. HS-hubs sold separately. One piece copper bus bar, 100 percent circuit breaker twistouts. Positive load side circuit breaker hook rail. Suitable for use as service equipment when a main breaker (125 amp maximum) is back-fed in a branch position, and used with main breaker retainer clip No. MBR1. When used as service equipment, any unused neutral position may be used for equipment grounding. Rotate entire device 180 degrees for bottom feed. Gray enamel finish. UL Listed, complies fully with NEC and UL requirements for Class CTL. 12-1/8" x 14-3/4" x 4-1/4". Outdoor NEMA 3R power inlet box. May be installed outdoors up to 100 feet from a home's load center so your generator can be plugged in outside, away from open doors or windows. Designed to be hard-wired directly to Reliance transfer switches with building wire. Has four combination 1/2" and 3/4" knockouts (one on each side, bottom and back). 6" height x 4" width x 2.63" depth. UL listed. Designed for residential or light commercial applications where duty is not severe. Meets or exceeds NEMA Enclosed Switch Standard KS1-1983 for type GD, CSA certified; 60 degrees C/75 degrees C conductor rating. Two pole, 120/240 volt AC; 250 volt DC. Removable closing cap. Accepts Class H fuses (not included). Feature quick make, quick break mechanism. Suitable for use as service entrance equipment when installed in accordance with National Electrical Code. 6-7/8" x 9-7/8" x 3-5/16".UL Listed (Enclosed Switches No. 98).
Reliance PB20 Outdoor Power Inlet Box Murray LNF222RU Non-Fusible Lever Safety Switch Cutler-Hammer MBE24L125BTS Main Lug Breakers
Outdoor NEMA 3R power inlet box. May be installed outdoors up to 100 feet from a home's load center so your generator can be plugged in outside, away from open doors or windows. Designed to be hard-wired directly to Reliance transfer switches with building wire. Has four combination 1/2" and 3/4" knockouts (one on each side, bottom and back). 6" height x 4" width x 2.63" depth. UL listed. Single phase, 2 pole, 3 wire, 240 volt, 10,000 AIC maximum, rated 10 HP maximum. Compact size, quick-make, quick-break mechanism, galvanized steel enclosure. Bottom cable entry and exit only, no hub provision supplied. Padlocking provisions to lock cover or lock in off position. Lugs suitable for copper or aluminum. Silver plated copper conductors. GSGK60 equipment ground kit sold separately. Number 14-3 AWG line and load wire range. 5-9/16" x 8-1/4" x 3-1/8". UL Listed file No.E4776, NEMA Type GD, meets federal specifications WS865C. BR branch breaker type, DS style hub, surface mount, EUSERC, 10kAIC. Bottom and top feed, ring style, UG/OH service. UL Listed.
Eaton BR1220B100 Load Center Square D UTRS213B Meter Sockets Siemens Energy SS102AX Murray Meter Sockets
Galvanized steel enclosure. Single phase, 3 wire, insulated/bondable split neutral, 12 (1") spaces, 20 poles, 120/240 volt.  Main breaker type BR at 10,000 AIR. Tin-plated aluminum bus bar. Twin neutral with non-removable cross bus. When bonded, unused neutral connections may be used for equipment ground protectors in service entrance application. #4 - 1/0 wire range. Electrostatic powder coat, baked urethane painted. Rotate 180 degrees for bottom feed; orientation of main breaker handle consistent with NEC 240-81 requirements because it operates horizontally. 14-5/16" x 18-3/4" x 3-7/8". UL Listed file E52977. Single phase, 3 wire, 4 jaw, 600 volt AC maximum. 10,000 rms symmetrical amp short circuit current rating. Hub provisions have an A-type size and its enclosure is made of aluminum. Supplied with bonded neutral. Requires bolt-on hub or closing plate (not included) for hub opening in top endwall. Bypass and jaw release sold separately. It can accommodate buildings supplied by overhead power lines or underground cables. UL Listed. Single phase, 3 wire, 4 jaw, 600 volt maximum 10,000 AIR. Jaws fabricated from high conductivity, tin plated, copper alloy. Insulating jaw support blocks of high impact, non-tracking thermoset polyester. Galvanized steel enclosure. Safety guides reduce chances of accidental contact, and aligns meter in sock. Uses RX style hub (not included). Provision for 5th jaw, no bypass. UL Listed.
Siemens E1020MB1100FCGP Remodel Load Center PowerMark Gold TLM1212RCUP Standard Convertible Load Center Square D QO816L100RBCP Load Center
Single phase, 3 wire, 10 spaces/20 circuits, 120/040 volt. 22,000 AIR. Use for older home renovation projects where the distance between the studs are narrower then current construction practices. One piece bus bar construction designed for use only with circuit breakers. Simple dead front adjustment after trim is installed. Positive load side circuit breaker hook rails. Two 15 amp single pole and one 30 amp double pole breakers included. 14-3/4" x 12-3/8"  3-7/8". UL Listed. Factory installed main lug, convertible to a main breaker. Single-phase, three-wire, 120/240 volt AC. One-piece interior removes and reinstalls easily. Full-length neutrals are easier to wire, reducing installation time and cost. Minimum 100 per cent neutral terminations. Sturdy copper bus and galvanized box increase durability and reliability. Combination slotted/Robertson screws speed wiring. All holes are rated for 14-4 wire. 100 per cent rated split neutral on each side. Load centers accept Q Line circuit breakers, including GE's exclusive 1/2"  THQPs. 100-225 amp devices have removable closing cap. (12) 1" or (24) 1/2"  spaces; 22000 AIC. 12-1/2" x 21-3/16" x 4-5/8". Main lug outdoor load center, 100 amp, 8 space/16 circuit, has a 2-1/2" maximum type B hub in the top end wall, a 1-1/2" maximum knockout in the bottom end wall and a B-cap covering on the 2" bushed opening. NEMA type 3R enclosure with a rainproof cover for outdoor use. ANSI Certified and UL Listed.
Speedfax S1224B1100 Convertible Load Center PowerMark Gold TM1210CCU Standard Load Center PowerMark Gold TM2010CCU Standard Load Center
Single phase, 3 wire, 22K A/C main breaker factory installed. Aluminum bus bar, tin plated. ANSI 61 gray powder coated. Suitable for use as service equipment when main breaker is installed or when not more than six main disconnecting means are provided. Convertible from main breaker to main lug. NEMA Type 1. 14.25" width x 3.88" depth. Single-phase, Three-wire, 120/240 volt AC. (12) 1" circuits or (24) 1/2" circuits. One-piece interior removes and reinstalls easily. Full-length neutrals are easier to wire, reducing installation time and cost. Minimum 100 percent neutral terminations. Sturdy copper bus and galvanized box increase durability and reliability. Combination slotted/Robertson screws speed wiring. All holes are rated for 14-4 wire. 100 per cent rated split neutral on each side. Load centers accept Q Line circuit breakers, including GE's exclusive 1/2" THQPs. 100-225 amp devices have removable closing cap. 22,000 AIC. 14" x 19" x 3-3/4". UL Listed. Single-phase, three-wire, 120/240 volt AC. (20) 1" spaces. One-piece interior removes and reinstalls easily. Full-length neutrals are easier to wire, reducing installation time and cost. Minimum 100 percent neutral terminations. Sturdy copper bus and galvanized box increase durability and reliability. Combination slotted/Robertson  screws speed wiring. All holes are rated for 14-4 wire. 100 per cent rated split neutral on each side. Load centers accept Q Line circuit breakers, including GE's exclusive 1/2"  THQPs. 100-225 amp devices have removable closing cap. 22,000 AIC. 14" x 23" x 3-3/4". UL Listed.
Speedfax S2020B1100 Convertible Load Center Square D URTRS213B Meter Sockets BRLC 125A 20/40CR AL BUS/WGB
Single phase, 3 wire, 22K A/C main breaker factory installed. Aluminum bus bar, tin plated. ANSI 61 gray powder coated. Suitable for use as service equipment when main breaker is installed or when not more than six main disconnecting means are provided. Convertible from main breaker to main lug. NEMA Type 1. 14.25" width x 3.88" depth. Single phase, 3 wire, 4 jaw, 600 volt AC maximum. Without bypass or jaw release. Steel enclosure material. Unit supplied with bonded neutral. 10,000 RMS symmetrical ampere short circuit current rating. Type-A hub provisions and the bottom end-wall has a 2-1/2" maximum knockout. Metering is utility specific. Always check with local utility company before installing. UL listed. Type BR single-phase, main lug loadcenters. Three-wire 120/240 Vac. Insulated/bondable split neutral, 20 spaces, 24 circuits, indoor, c1 box size. Has notch for BREQS125 hold-down kit. Combination cover style. Ground bar GBK1220 installed.
Speedfax S2040B1200 Convertible Load Center LOAD CENTER 100A 1P3W 120/240V Murray W0204MB1100 Load Center
Single phase, 3 wire, 22K A/C main breaker factory installed. Aluminum bus bar, tin plated. ANSI 61 gray powder coated. Suitable for use as service equipment when main breaker is installed or when not more than six main disconnecting means are provided. Convertible from main breaker to main lug. NEMA Type 1. 14.25" width x 3.88" depth. Value kit, indoor. Includes a sturdy highly-conductive tin-plated copper buss bar and a rust-resistant galvanized box. Indoor NEMA 1 enclosure with combination surface/flush front. Factory-installed main lug, full-length neutral bars, top or bottom feed and self-adjusting, dead-front cover. One-piece interior removes and re-installs easily. Single-phase, 3-wire, 120/240-volt and 22K AIC rating. All holes are rated for 14-4 wire and 100 percent rated split neutrals on each side. Accepts Q-Line THQL standard, GFCI and AFCI circuit breakers, including GE's exclusive 1/2" THQPs. UL Listed and ANSI Certified. 16" height x 14" width x 3.375" depth, 16.79 lb. Single phase, 2 spaces/4 circuits, 120/240 volt. 10,000 AIR. Factory installed main breaker. Additional spaces allow connection of external circuits such as yard lights. One 1-1/4" HS125 hub included. Normally used as a means of disconnecting power to a mobile home panel, but also used as a disconnect for houses. Aluminum bus bar insulates and secures interior. Gray enamel finish. Pole mountable. UL Listed for use as service entrance equipment.
Murray LW102NLU Load Center Murray LC2040B1100 Rock Solid Load Center LOAD CENTR 125A 12SPACE 24CIR
Single phase, 2 spaces/4 circuits, 120/240 volt. 10,000 AIR. Factory installed main breaker. Additional spaces allow connection of external circuits such as yard lights. One 1-1/4" HS125 hub included. Normally used as a means of disconnecting power to a mobile home panel, but also used as a disconnect for houses. Aluminum bus bar insulates and secures interior. Gray enamel finish. Pole mountable. 12-1/2" height x 6" width x 4-1/4" depth. UL Listed for use as service entrance equipment. Main breaker load center. 100 amp Single phase, 3 wire, split neutral, 20 spaces/40 circuits. 120/240 volt. Indoor with combination surface/flush cover. 22,000 AIC rating. Aluminum bus bar. One piece steel interior allows for easy removal. Keyhole and nail slots provide easy enclosure mounting. Knockout patterns sized for maximum wiring flexibility. UL Listed. Value kit, indoor. Includes a sturdy highly-conductive tin-plated copper buss bar and a rust-resistant galvanized box. Indoor NEMA 1 enclosure with combination surface/flush front. Factory-installed main lug, full-length neutral bars, top or bottom feed and self-adjusting, dead-front cover. One-piece interior removes and re-installs easily. Single-phase, 3-wire, 120/240-volt and 22K AIC rating. All holes are rated for 14-4 wire and 100 percent rated split neutrals on each side. Accepts Q-Line THQL standard, GFCI and AFCI circuit breakers, including GE's exclusive 1/2" THQPs. UL Listed and ANSI Certified. 16" height x 14" width x 3.375" depth, 16.79 lb.
BRLC 100A MN 20/40 CR         Square D QO112M100C Load Center Cutler-Hammer UGHTRS213BE Meter Sockets
BR style 1-inch loadcenter, main circuit breaker, no feed-thru lugs, 100A, single-phase, 40-pole, 40 circuits, 20 spaces, 120/240V, #4-1/0 AWG Cu/Al at 60 or 75 degreesC wire, Three-wire, NEMA 1 enclosure, d1 box size. Interrupt Rating 25 kAIC. Aluminum bus. Combination mounting. 5.19 in x 14.31 in x 25 in. UL 50, UL 67. Cover included. Welded sheet steel. Single phase, 3 wire, split neutral, 12 spaces/12 circuit, 120/240 volt. 22,000 AIR factory installed main breaker. Comes with a ground bar and a combination cover for added protection. Shielded copper bus bar. 2-1/2" knockouts located on the top and bottom. Accepts QO circuit breakers and is compatible with overhead and underground service feeds. UL Listed. Single meter socket, ringless, horn bypass, 5 terminals, 200 amp, 600 volt AC, OH/UG service, hub provision only, grounded fifth terminal, service ground lug #14-2 Cu/Al. Wire size range 1/0 - 350. UL Labeled. 16" x 12" x 6". Suitable for either top or bottom service cable entry.
Reliance PB50 Outdoor Power Inlet Box Eaton BR1224L200R Load Center BRLC 200A 20/40 CR ALBUS/WGB
Outdoor NEMA 3R power inlet box. May be installed outdoors up to 100 feet from a home's load center so your generator can be plugged in outside, away from open doors or windows. Designed to be hard-wired directly to Reliance transfer switches with building wire. Has four combination 1/2" and 3/4" knockouts (one on each side, bottom and back). 6" height x 4" width x 2.63" depth. UL listed. Rainproof galvanized steel enclosure. Single phase, 3 wire, insulated/bondable split neutral, 12 (1") spaces 24 poles, 120/240 volt AC. Has notch for No.BRHDK125 hold down kit. With closure plates, hubs and ground bar kits (necessary for sub-feeding) sold separately. Tin-plated aluminum bus bar. In accordance with NEC, suitable for use as service equipment when not more than 6 main disconnecting means are provided and when not used as lighting and appliance panelboard. Twin neutral with non-removable cross bus. When bonded, unused neutral connections may be used for equipment ground protectors in service entrance application. #1 - 300 kcmil wire. Electrostatic powder coat, baked urethane painted. B2R box 14-5/16" x 18-3/4" x 5-3/16". UL Listed file E52977. BR style 1-inch loadcenter, main lug, ground bar, includes BREQS125 hold-down screw, 200A, single-phase, 40-pole, 40 circuits, 20 spaces, 120/240V, #1-300 kcmil Cu/Al at 60 degreesC or 75 degreesC wire, three-wire NEMA 1 enclosure, c2 box size. Cover included. 3.88 in x 14.31 in x 23 in. Has notch for brhdk125 hold-down kit.
POWER PANEL RV 70A 50/20A GFCI Reliance Controls TF151W Generator Transfer Switches Murray LC1224B1100 Load Center
Unmetered RV outlet box. Rugged 16-gauge zinc coated G-90 steel, with electro-deposition finish resists corrosion and fading. NEMA 3R rainproof enclosure protects against weather, vandalism and nuisance tripping. Factory wired, assembled and tested. All-in-1 construction for factory assured terminations. Suitable for use as service entrance equipment when installed in accordance with the National Electric Code. Accepts copper or aluminum wire for added installation flexibility. Rolled edge door for cord protection. Dead front construction prevents accidental contact with live parts. Stay open position on door for convenience. Padlock provision. UL/CUL Listed (Power Outlets). Economical, allows powering an otherwise hard-wired furnace blower motor with a portable generator for heat and to prevent frozen pipes during a power outage. Uses standard 15 amp extension cord. Full-color packaging. UL1008 Listed. Single phase 3 wire; 120/240 volt; 24 circuits maximum. Twelve 1" spaces. Combination cover, 10,000 AIC. 100 amp main breaker included. 18-5/8" x 13-1/8" x 4". UL listed.
LOADCENTER 100A 20/40 VP      Eaton BR1020B100RF Load Center Siemens Energy MC1020B1100S Meter Socket Load Centers
BR style 1-inch loadcenter, main circuit breaker, value pack, 100A, single-phase, 40-pole, 40 circuits, 20 spaces, 120/240V. Wire size #4-1/0 AWG Cu/Al at 60 or 75 degreesC, NEMA 1 enclosure, d1 box size. Aluminum bus, combination mounting. 3.88 in x 14.31 in x 18.75 in. Includes 6-br120. Cover included. Rainproof galvanized steel enclosure. Single phase, 3 wire, insulated/bondable split neutral, 10 (1") spaces, 20 poles, 120/240 volt AC. Main breaker type BR at 10,000 AIC. Includes feed thru lugs for both phase and neutral conductors. With hub closure plates, hubs and ground bar kit (necessary for sub-feeding) sold separately. Tin plated aluminum bus bar. Twin neutral with non-removable cross bus connecting them. When bonded, unused neutral connections may be used for equipment ground protectors in service entrance application. #4 - 1/0 wire range. Electrostatic powder coat, baked urethane painted. Rotate 180 degrees for bottom feed; orientation of main breaker handle consistent with NEC 240-81 requirements because it operates horizontally. 14-5/16" x 18-3/4" x 5-3/16". UL Listed file E52977. Combination meter socket. Surface mount, overhead service entrance only. 100 amp maximum, 100 amp main breaker installed. Single phase, 3 wire. 10 spaces, 20 circuits, 22,000 AIC rating. Nema type 3R outdoor enclosure. Uses RX style hub, not included.
Speedfax S3040B1200 Convertible Load Center Midwest UG412RMW250 Spa Panel PowerMark Gold TM820RCUFLP Load Center
Single phase, 3 wire, 22K A/C main breaker factory installed. Aluminum bus bar, tin plated. ANSI 61 gray powder coated. Suitable for use as service equipment when main breaker is installed or when not more than six main disconnecting means are provided. Convertible from main breaker to main lug. NEMA Type 1. 14.25" width x 3.88" depth. Single phase, 2 or 4 breaker spaces. 50 amp GFI protection rating. Moisture resistant use around water heaters, swimming pools, spas, hot tubs, garden tubs, pools, etc. Includes 2 pole 50 amp ground fault breaker. Factory Installed main breaker. Single phase, three wire, 120/240 volt AC. (8) 1" or (16) 1/2" spaces; 22,000 AIC. One piece interior removes and reinstalls easily. Full length neutrals are easier to wire, reducing installation time and cost. Minimum 100 per cent neutral terminations. Sturdy copper bus and galvanized box increase durability and reliability. Combination slotted/Robertson screws speed wiring. All holes are rated for 14-4 wire. 100 per cent rated split neutral on each side. Load centers accept Q Line circuit breakers, including GE 1/2" THQP. 100-225 amp devices have removable closing cap. 12-1/2" x 28-11/16" x 4-5/8". UL Listed.
PowerMark Gold TM2020CCUP Load Center Eaton BR2040B200 Load Center Siemens Energy MC1224B1100EFC Meter Socket Load Centers
Single-phase, three-wire, 120/240 volt AC. (20) 1", (40) 1/2" spaces. One-piece interior removes and reinstalls easily. Full-length neutrals are easier to wire, reducing installation time and cost. 100 percent neutral terminations. Sturdy copper bus and galvanized box increase durability and reliability. Combination slotted/Robertson screws speed wiring. All holes are rated for 14-4 wire. 100 per cent rated split neutral on each side. Load centers accept Q Line circuit breakers, including GE's exclusive 1/2" THQPs. 100-225 amp devices have removable closing cap. 22,000 AIC. 14" x 28-7/16" x 3-3/4". UL Listed. Steel enclosure. Single phase, 3 wire, insulated/bondable split neutral, 20 (1") spaces, 40 circuits, 120/240 volt. Main breaker type BWH at 25,000 AIC. Tin-plated aluminum bus bar. Twin neutral with non-removable cross bus connecting them. When bonded, unused neutral connections may be used for equipment ground protectors in service entrance application. Number 2 - 300 kcmil wire range. Electrostatic powder coat, baked urethane painted. Orientation of main breaker handle consistent with NEC 240-81 requirements because it operates horizontally. UL Listed file E52977. 14-5/16" width x 29-1/8" height x 3-7/8" depth. Combination meter socket. flush mount, 100 amp maximum, 100 amp main breaker installed. Single phase, 3 wire. 22,000 AIC rating. Aluminum bus bars. Nema type 3R outdoor enclosure. Complies with EUSERC Dwg. No. 301.
Siemens ES S3030B1150 Convertible Load Center LOAD CNTR 200A 20SP 32C INDOOR BR SPA 50A ST   GFI
Single phase, 3 wire, 22K A/C main breaker factory installed. Aluminum bus bar, tin plated. ANSI 61 gray powder coated. Suitable for use as service equipment when main breaker is installed or when not more than six main disconnecting means are provided. Convertible from main breaker to main lug. NEMA Type 1. 14.25" width x 3.88" depth. Value kit, indoor. Includes a sturdy highly-conductive tin-plated copper buss bar and a rust-resistant galvanized box. Indoor NEMA 1 enclosure with combination surface/flush front. Factory-installed main lug, full-length neutral bars, top or bottom feed and self-adjusting, dead-front cover. One-piece interior removes and re-installs easily. Single-phase, 3-wire, 120/240-volt and 22K AIC rating. All holes are rated for 14-4 wire and 100 percent rated split neutrals on each side. Accepts Q-Line THQL standard, GFCI and AFCI circuit breakers, including GE's exclusive 1/2" THQPs. UL Listed and ANSI Certified. 16" height x 14" width x 3.375" depth, 16.79 lb. Spa panel, wire size - number 8-2 Cu/Al. 60 or 75 degreesC. NEMA 3R enclosure. Box size - 5R. Includes factory installed breaker, ground-fault self test. 10.2 In X 4.9 In X 4.3 In, 4.45 lb. UL Listed.
Murray LW204TL Load Center GE Electrical TSM420CSCUP Powermark Gold Meter Socket Load Centers Eaton BR816B200RF Load Center
Single phase, 4 spaces/8 circuits, 120/240 volt. 10,000 AIR. Factory installed main breaker. Additional spaces allow connection of external circuits such as yard lights. One 2" HS200 hub included. Normally used as a means of disconnecting power to a mobile home panel, but also used as a disconnect for houses. Aluminum bus bar insulates and secures interior. Drop hinge door. Gray enamel finish. Pole mountable. UL Listed for use as service entrance equipment. Feed through lugs. Single phase, 3 wire, bonded neutral, 8 total 1-pole spaces, 120/240 volt AC. 10,000 AIC. Four 1-pole or two 2-pole 1" THQL spaces, eight 1-pole or three 2-pole 1/2" THQP spaces. Main breaker factory installed. 6-350 main wire size. Padlock provisions on door. Hinged door is removable for safety and convenience. 14" x 28" x 4-1/2" UL Listed. Meets EUSERC requirements. Rainproof galvanized steel enclosure. Single phase, 3 wire, insulated/bondable neutral, 8 (1") spaces, 16 circuits, 120/240 volt AC. Main breaker type BWH at 25,000 AIC. Includes feed thru lugs for both phase and neutral conductors. With hub closure plates, hubs and ground bar kit (necessary for sub-feeding) sold separately. Tin plated aluminum bus bar. Neutral is movable to other side. When bonded, unused neutral connections may be used for equipment ground protectors in service entrance application. #2 - 300 kcmil wire range. Electrostatic powder coat, baked urethane painted. Rotate 180 degrees for bottom feed; orientation of main breaker handle consistent with NEC 240-81 requirements because it operates horizontally. 14-5/16" x 25" x 5-3/16". UL Listed file E8741.
Speedfax S3040B1200P Convertible Load Center Speedfax S4040B1200 Convertible Load Center Speedfax MC0408B1200RT Load Center
Single phase, 3 wire, 22K A/C main breaker factory installed. Aluminum bus bar, tin plated. ANSI 61 gray powder coated. Suitable for use as service equipment when main breaker is installed or when not more than six main disconnecting means are provided. Convertible from main breaker to main lug. NEMA Type 1. 14.25" width x 3.88" depth. Single phase, 3 wire, 22K A/C main breaker factory installed. Aluminum bus bar, tin plated. ANSI 61 gray powder coated. Suitable for use as service equipment when main breaker is installed or when not more than six main disconnecting means are provided. Convertible from main breaker to main lug. NEMA Type 1. 14.25" width x 3.88" depth. Combination meter socket. 200 amp main breaker installed, Single phase, 3 wire, insta-wire neutrals. 4 spaces, 8 circuits. 120/240 volt.  22,000 AIC rating. 4 jaws. Tin plated copper bus bars. Nema type 3R outdoor enclosure. Overhead or underground feed. Feed thru lugs provided. Key hole shaped mounting holes for easy hanging. Deadfront pull ring and side hinge door. Captive dead front screw. RX style hub sold separately. UL Listed.
Speedfax MC0408B1200T Load Center Square D QO Circuit Breaker Enclosure Speedfax S4040B1200P Convertible Load Center
Combination meter socket. 200 amp main breaker installed, Single phase, 3 wire, insta-wire neutrals. 4 spaces, 8 circuits. 120/240 volt.  22,000 AIC rating. 4 jaws. Tin plated copper bus bars. Nema type 3R outdoor enclosure. Overhead or underground feed. Feed thru lugs provided. Key hole shaped mounting holes for easy hanging. Deadfront pull ring and side hinge door. Captive dead front screw. RX style hub sold separately. UL Listed. Outdoor circuit breaker enclosure, 200 amp. NEMA type 3R for exterior use. Includes a QOM2200VH circuit breaker and a QOM22225NRB enclosure.  UL Listed. Single phase, 3 wire, 22K A/C main breaker factory installed. Aluminum bus bar, tin plated. ANSI 61 gray powder coated. Suitable for use as service equipment when main breaker is installed or when not more than six main disconnecting means are provided. Convertible from main breaker to main lug. NEMA Type 1. 14.25" width x 3.88" depth.
Murray LC2040B1200 Rock Solid Load Center PowerMark Gold TM2020CCUPL5 Contractor Load Center Kit BRLC 200A 40/40 CR ALBUS/WGB
Single phase, 3 wire, split neutral, 20 spaces/40 circuits. 120/240 volt. 200 amp main breaker loadcenter. Indoor with combination surface/flush cover. 22,000 AIC rating. Aluminum bus bar. One piece steel interior allows for easy removal. Keyhole and nail slots provide easy enclosure mounting. Knockout patterns sized for maximum wiring flexibility. UL Listed. Includes 1 number TM2020CCU, 200 amp, indoor load center, 6 THQL single pole 20 amp, 1 THQL double pole 30 amp and 1 THQL double pole 50 amp. 40 maximum 1 pole 1/2" spaces, 20 maximum 1" spaces. UL Listed. BR style 1-inch loadcenter, main lug, ground bar, 200A, single-phase, 40-pole, 40 circuits, 40 spaces, 120/240V, #1-300 kcmil Cu/Al at 60 or 75 degreesC, NEMA 1 enclosure, G1 box size. Aluminum bus, Three-wire. Cover included. 3.88 in x 14.31 in x 34.13 in, 34 lb. Has notch for brhdk125 hold-down kit. UL 67, UL 50.
Eaton MBT48B200BTS All-in-One Ringless Meter Breaker/Center Siemens EQ W0404MB1200CT Load Center Eaton MBT48B125BTS All-in-One Ringless Meter Breaker/Center
All-In-One combination service entrance (includes distribution section), BR branch breaker type - Non-EUSERC, 25 kAIC, 4/8 distribution, 4 jaws, main breaker included. Bottom and top feed breaker, ringless security, OH/UG service. 12.50" height x 14.44" width x 4.00" depth. Wire size range Cu/Al  60 degrees C. Uses a DS-series hub, sold separately. Single phase, 4 spaces/4 circuits, 120/240 volt. 10,000 AIR. Factory installed main breaker. Additional spaces allow connection of external circuits such as yard lights. One 2" HS200 hub included. Normally used as a means of disconnecting power to a mobile home panel, but also used as a disconnect for houses. Aluminum bus bar insulates and secures interior. Drop hinge door. Gray enamel finish. Pole mountable. UL Listed for use as service entrance equipment. All-In-One combination service entrance (includes distribution section), BR branch breaker type - Non-EUSERC, 25 kAIC, 4/8 distribution, 4 jaws, main breaker included. Bottom and top feed breaker, ringless security, OH/UG service. 12.50" height x 14.44" width x 4.00" depth. Wire size range Cu/Al  60 degrees C. Uses a DS-series hub, sold separately.
LOAD CNTR 200A 20SP 32C OUTDOR Eaton BR3040B200V Load Center PowerMark Gold TM4020CCU Standard Load Center
Value kit includes outdoor 200-amp main breaker load center, 3 20-amp single-pole and 1 30-amp double-pole THQP 1/2" circuit breakers. Includes a sturdy highly-conductive tin-plated copper buss bar and a rust-resistant galvanized box. Outdoor NEMA 3R enclosure. Factory-installed main breaker, full-length neutral bars, top or bottom feed and self-adjusting, dead-front cover. One-piece interior removes and re-installs easily. Single-phase, 3-wire, 120/240-volt and 22K AIC rating. All holes are rated for 14-4 wire and 100 percent rated split neutrals on each side. Accepts Q-Line THQL standard, GFCI and AFCI circuit breakers, including GE's exclusive 1/2-in THQPs. UL Listed and ANSI Certified. 34.19" height x 14.69" width x 5.23" depth, 43 lb. Galvanized steel enclosure. Single phase, 3 wire, insulated/bondable split neutral, 30 (1") spaces, 40 poles, 120/240 volt. Main breaker type BW at 25,000 AIC. Ground bar kit (necessary for sub-feeding) sold separately. Tin plated aluminum bus bar. Twin neutral with non removable cross bus. When bonded, unused neutral connections may be used for equipment ground protectors in service entrance application. #2 - 300 kcmil wire range. Electrostatic powder coat, baked urethane painted. Rotates 180 degrees for bottom feed; orientation of main breaker handle consistent with NEC 240-81 requirements because it operates horizontally. G1 box - 14-5/16" width x 34-1/8" height x 3-7/8" depth. UL Listed file E52977. Single-phase, three-wire, 120/240 volt AC. (40) 1" spaces; 22,000 AIC. One piece interior removes and reinstalls easily. Full-length neutrals are easier to wire, reducing installation time and cost. 100 percent neutral terminations. Sturdy copper bus and galvanized box increase durability and reliability. Combination slotted/Robertson screws speed wiring. All holes are rated for 14-4 wire. 100 per cent rated split neutral on each side. Load centers accept Q Line circuit breakers, including GE's exclusive 1/2" THQPs. Removable closing cap. 14" x 39-3/16" x 3-3/4". UL Listed.
   
 
1 2