Home > ELECTRICAL > ROUGH ELECTRICAL > FUSES & BREAKERS
Sort By:
1 2 3
Bussmann AGX-7X5-RP Electronic Fast Acting Fuse with Clip Strips Bussmann Fusetron NON-15 Cartridge Bussmann Fusetron NON-25 Cartridge
Fast acting, 1/4 x 1" glass tube fuse. 125 volt maximum. For general purpose circuits, protects lighting, heating and other circuits not subject to temporary surges and where available short-circuit currents are relatively low. Does not have any appreciable degree of time delay and should not be specified in circuits where large transients or motor overloads occur. Single element type. The counterpart of type W plug fuses. Use in non-motor circuits. 50,000 AIR. 250 volt maximum. UL Listed. For general purpose circuits, protects lighting, heating and other circuits not subject to temporary surges and where available short-circuit currents are relatively low. Does not have any appreciable degree of time delay and should not be specified in circuits where large transients or motor overloads occur. Single element type. The counterpart of type W plug fuses. Use in non-motor circuits. 50,000 AIR. 250 volt maximum. UL Listed.
Bussmann NON Cartridge Low Voltage Fast Acting Fuse Bussmann NON Cartridge Low Voltage Fast Acting Fuse Bussmann ABC-20 Electronic Fast Acting Fuse
For general purpose circuits, protects lighting, heating and other circuits not subject to temporary surges and where available short-circuit currents are relatively low. Does not have any appreciable degree of time delay and should not be specified in circuits where large transients or motor overloads occur. Single element type. The counterpart of type W plug fuses. Use in non-motor circuits. 50,000 AIR. 250 volt maximum. UL Listed. For general purpose circuits, protects lighting, heating and other circuits not subject to temporary surges and where available short-circuit currents are relatively low. Does not have any appreciable degree of time delay and should not be specified in circuits where large transients or motor overloads occur. Single element type. The counterpart of type W plug fuses. Use in non-motor circuits. 50,000 AIR. 250 volt maximum. UL Listed. Ceramic tube construction, for use in microwave ovens. 1/4" x 1-1/4" physical size, CSA certified, UL Listed.
Bussmann ABC Electronic Miniature Fast Acting Fuse Bussmann MDL Electronic Miniature Time Delay Fuse FUSE PARTY LIGHT HOLIDAY
Ceramic tube construction, for use in microwave ovens. 1/4" x 1-1/4" physical size, CSA certified, UL Listed. Glass tube. Plated brass end caps. 1/4" x 1 1/4". 250 volt AC rating maximum. UL Listed. Fast-acting 3 amp fuses.
Bussmann MAS-3X5 Electronic Fast Acting Fuse with Clip Strips HomeLine HOM140CP Standard Circuit Breaker Bussmann ABC-10 Electronic Fast Acting Fuse
Fast-acting 3 amp fuses. Single-pole 1" circuit breaker features 10,000 AIR and 120/240 VAC. Uses a thermal-magnetic tripping mechanism for overload and short-circuit protection. Compatible with Homeline load centers and CSED devices. ANSI certified and UL Listed. Ceramic tube construction, for use in microwave ovens. 1/4" x 1-1/4" physical size, CSA certified, UL Listed.
HomeLine HOM130CP Standard Circuit Breaker HomeLine HOM115CP Standard Circuit Breaker HomeLine HOM120CP Standard Circuit Breaker
Single-pole 1" circuit breaker features 10,000 AIR and 120/240 VAC. Uses a thermal-magnetic tripping mechanism for overload and short-circuit protection. Compatible with Homeline load centers and CSED devices. ANSI certified and UL Listed. Single-pole 1" circuit breaker features 10,000 AIR and 120/240 VAC. Uses a thermal-magnetic tripping mechanism for overload and short-circuit protection. Compatible with Homeline load centers and CSED devices. ANSI certified and UL Listed. Single-pole 1" circuit breaker features 10,000 AIR and 120/240 VAC. Uses a thermal-magnetic tripping mechanism for overload and short-circuit protection. Compatible with Homeline load centers and CSED devices. ANSI certified and UL Listed.
Bussmann MDL-4 Electronic Time Delay Fuse Bussmann NON Cartridge Low Voltage Fast Acting Fuse Eaton BR115 Type BR Miniature Circuit Breaker
Glass tube. Plated brass end caps. 1/4" x 1 1/4". 250 volt AC rating maximum. UL Listed. For general purpose circuits, protects lighting, heating and other circuits not subject to temporary surges and where available short-circuit currents are relatively low. Does not have any appreciable degree of time delay and should not be specified in circuits where large transients or motor overloads occur. Single element type. The counterpart of type W plug fuses. Use in non-motor circuits. 50,000 AIR. 250 volt maximum. UL Listed. Switching duty rating. Thermal magnetic 40 degrees C. Interchangeable, will replace: Bryant, Westinghouse and Challenger. Type BR. 120/240 volt, 10,000 AIR. 1" per pole.
Bussmann MDL-7 Electronic Time Delay Fuse Bussmann Fusetron NON-35 Cartridge Bussmann MDL-8 Electronic Time Delay Fuse
Glass tube. Plated brass end caps. 1/4" x 1 1/4". 250 volt AC rating maximum. UL Listed. For general purpose circuits, protects lighting, heating and other circuits not subject to temporary surges and where available short-circuit currents are relatively low. Does not have any appreciable degree of time delay and should not be specified in circuits where large transients or motor overloads occur. Single element type. The counterpart of type W plug fuses. Use in non-motor circuits. 50,000 AIR. 250 volt maximum. UL Listed. Glass tube. Plated brass end caps. 1/4" x 1 1/4". 250 volt AC rating maximum. UL Listed.
Bussmann MDL-10 Electronic Time Delay Fuse Bussmann Fusetron NON-45 Cartridge GE THQL1120 Type THQL Q-Line Standard Circuit Breaker
Glass tube. Plated brass end caps. 1/4" x 1 1/4". 250 volt AC rating maximum. UL Listed. For general purpose circuits, protects lighting, heating and other circuits not subject to temporary surges and where available short-circuit currents are relatively low. Does not have any appreciable degree of time delay and should not be specified in circuits where large transients or motor overloads occur. Single element type. The counterpart of type W plug fuses. Use in non-motor circuits. 50,000 AIR. 250 volt maximum. UL Listed. Copper-to-copper connections, calibrated for optimum trip performance, heat resistant thermoset cases and covers, cemented calibration screw. Type THQL - 1" per pole. May be used, when marked to accept, with American Switch, Arrow Hart, Bryant, General Switch, GTE, Sylvania, most ITE, Murray, Westinghouse Type BR, Challenger and Crouse-Hinds. 15 to 30 amp 14 - 8 Cu or 12 - 8 Al AWG wire, 35 to 60 amp 8 - 3 Cu or 8 - 2 Al AWG wire. UL Listed, HACR rated. 1" module, 120/240 volt; 10,000 AIR.
GE THQL1130 Type THQL Q-Line Standard Circuit Breaker GE THQL1140 Type THQL Q-Line Standard Circuit Breaker GE THQL1150 Type THQL Q-Line Standard Circuit Breaker
Copper-to-copper connections, calibrated for optimum trip performance, heat resistant thermoset cases and covers, cemented calibration screw. Type THQL - 1" per pole. May be used, when marked to accept, with American Switch, Arrow Hart, Bryant, General Switch, GTE, Sylvania, most ITE, Murray, Westinghouse Type BR, Challenger and Crouse-Hinds. 15 to 30 amp 14 - 8 Cu or 12 - 8 Al AWG wire, 35 to 60 amp 8 - 3 Cu or 8 - 2 Al AWG wire. UL Listed, HACR rated. 1" module, 120/240 volt; 10,000 AIR. Copper-to-copper connections, calibrated for optimum trip performance, heat resistant thermoset cases and covers, cemented calibration screw. Type THQL - 1" per pole. May be used, when marked to accept, with American Switch, Arrow Hart, Bryant, General Switch, GTE, Sylvania, most ITE, Murray, Westinghouse Type BR, Challenger and Crouse-Hinds. 15 to 30 amp 14 - 8 Cu or 12 - 8 Al AWG wire, 35 to 60 amp 8 - 3 Cu or 8 - 2 Al AWG wire. UL Listed, HACR rated. 1" module, 120/240 volt; 10,000 AIR. Copper-to-copper connections, calibrated for optimum trip performance, heat resistant thermoset cases and covers, cemented calibration screw. Type THQL - 1" per pole. May be used, when marked to accept, with American Switch, Arrow Hart, Bryant, General Switch, GTE, Sylvania, most ITE, Murray, Westinghouse Type BR, Challenger and Crouse-Hinds. 15 to 30 amp 14 - 8 Cu or 12 - 8 Al AWG wire, 35 to 60 amp 8 - 3 Cu or 8 - 2 Al AWG wire. UL Listed, HACR rated. 1" module, 120/240 volt; 10,000 AIR.
GE THQL1115 Type THQL Q-Line Standard Circuit Breaker GE THQP150 Type THQP Q-Line Standard Circuit Breaker GE THQP140 Type THQP Q-Line Standard Circuit Breaker
Copper-to-copper connections, calibrated for optimum trip performance, heat resistant thermoset cases and covers, cemented calibration screw. Type THQL - 1" per pole. May be used, when marked to accept, with American Switch, Arrow Hart, Bryant, General Switch, GTE, Sylvania, most ITE, Murray, Westinghouse Type BR, Challenger and Crouse-Hinds. 15 to 30 amp 14 - 8 Cu or 12 - 8 Al AWG wire, 35 to 60 amp 8 - 3 Cu or 8 - 2 Al AWG wire. UL Listed, HACR rated. 1" module, 120/240 volt; 10,000 AIR. Copper-to-copper connections, calibrated for optimum trip performance, heat resistant thermoset cases and covers, cemented calibration screw. Nearly identical to Type THQL with the same design and performance, yet only taking up 1/2 the space,  1/2" per pole. UL Listed, HACR rated. 15 and 20 amp SWD, switching duty rated, suitable for 120 volt fluorescent lighting loads. 15 to 25 amp #14 - 8 Cu or #12 - 8 Al AWG wire, 30 to 50 amp #8 - 4 Cu or #8 - 2 Al AWG wire. 3-9/32" height x 1/2" width x 2-3/8" depth. 120/240 volt; 10,000 AIR. Copper-to-copper connections, calibrated for optimum trip performance, heat resistant thermoset cases and covers, cemented calibration screw. Nearly identical to Type THQL with the same design and performance, yet only taking up 1/2 the space,  1/2" per pole. UL Listed, HACR rated. 15 and 20 amp SWD, switching duty rated, suitable for 120 volt fluorescent lighting loads. 15 to 25 amp #14 - 8 Cu or #12 - 8 Al AWG wire, 30 to 50 amp #8 - 4 Cu or #8 - 2 Al AWG wire. 3-9/32" height x 1/2" width x 2-3/8" depth. 120/240 volt; 10,000 AIR.
GE THQP130 Type THQP Q-Line Standard Circuit Breaker GE THQP120 Type THQP Q-Line Standard Circuit Breaker GE THQP115 Type THQP Q-Line Standard Circuit Breaker
Copper-to-copper connections, calibrated for optimum trip performance, heat resistant thermoset cases and covers, cemented calibration screw. Nearly identical to Type THQL with the same design and performance, yet only taking up 1/2 the space,  1/2" per pole. UL Listed, HACR rated. 15 and 20 amp SWD, switching duty rated, suitable for 120 volt fluorescent lighting loads. 15 to 25 amp #14 - 8 Cu or #12 - 8 Al AWG wire, 30 to 50 amp #8 - 4 Cu or #8 - 2 Al AWG wire. 3-9/32" height x 1/2" width x 2-3/8" depth. 120/240 volt; 10,000 AIR. Copper-to-copper connections, calibrated for optimum trip performance, heat resistant thermoset cases and covers, cemented calibration screw. Nearly identical to Type THQL with the same design and performance, yet only taking up 1/2 the space,  1/2" per pole. UL Listed, HACR rated. 15 and 20 amp SWD, switching duty rated, suitable for 120 volt fluorescent lighting loads. 15 to 25 amp #14 - 8 Cu or #12 - 8 Al AWG wire, 30 to 50 amp #8 - 4 Cu or #8 - 2 Al AWG wire. 3-9/32" height x 1/2" width x 2-3/8" depth. 120/240 volt; 10,000 AIR. Copper-to-copper connections, calibrated for optimum trip performance, heat resistant thermoset cases and covers, cemented calibration screw. Nearly identical to Type THQL with the same design and performance, yet only taking up 1/2 the space,  1/2" per pole. UL Listed, HACR rated. 15 and 20 amp SWD, switching duty rated, suitable for 120 volt fluorescent lighting loads. 15 to 25 amp #14 - 8 Cu or #12 - 8 Al AWG wire, 30 to 50 amp #8 - 4 Cu or #8 - 2 Al AWG wire. 3-9/32" height x 1/2" width x 2-3/8" depth. 120/240 volt; 10,000 AIR.
Bussmann MDL Electronic Miniature Time Delay Fuse Bussmann MDL Electronic Miniature Time Delay Fuse Bussmann MDL Electronic Miniature Time Delay Fuse
Glass tube. Plated brass end caps. 1/4" x 1 1/4". 250 volt AC rating maximum. UL Listed. Glass tube. Plated brass end caps. 1/4" x 1 1/4". 250 volt AC rating maximum. UL Listed. Glass tube. Plated brass end caps. 1/4" x 1 1/4". 250 volt AC rating maximum. UL Listed.
Bussmann NON Cartridge Low Voltage Fast Acting Fuse Bussmann NON Cartridge Low Voltage Fast Acting Fuse MES MP115 Type MP-T Circuit Breaker
For general purpose circuits, protects lighting, heating and other circuits not subject to temporary surges and where available short-circuit currents are relatively low. Does not have any appreciable degree of time delay and should not be specified in circuits where large transients or motor overloads occur. Single element type. The counterpart of type W plug fuses. Use in non-motor circuits. 50,000 AIR. 250 volt maximum. UL Listed. For general purpose circuits, protects lighting, heating and other circuits not subject to temporary surges and where available short-circuit currents are relatively low. Does not have any appreciable degree of time delay and should not be specified in circuits where large transients or motor overloads occur. Single element type. The counterpart of type W plug fuses. Use in non-motor circuits. 50,000 AIR. 250 volt maximum. UL Listed. One 1" space per pole. Will replace American Switch, Westinghouse Type BR, Bryant, Challenger, Sylvania, Crouse-Hinds, Murray, Frank Adams, General Electric (Full size only), General Switch, I-TE, Gould, Montgomery Ward and Sears. UL Listed, SWD rated. 120 volt AC fluorescent lighting. 120 volt AC; 10,000 AIR.
MES MP130 Type MP-T Circuit Breaker MES Q130 Standard Miniature Circuit Breaker HomeLine HOM115C Miniature Standard Circuit Breaker
One 1" space per pole. Will replace American Switch, Westinghouse Type BR, Bryant, Challenger, Sylvania, Crouse-Hinds, Murray, Frank Adams, General Electric (Full size only), General Switch, I-TE, Gould, Montgomery Ward and Sears. UL Listed, SWD rated. 120 volt AC fluorescent lighting. 120 volt AC; 10,000 AIR. Non-interchangeable trip. 120 volt AC; 10,000 AIR. Will replace American Switch, Westinghouse Type BR, Bryant, Challenger, Sylvania, Crouse-Hinds, Murray, Frank Adams, General Electric (Full size only), General Switch, I-TE, Gould, Montgomery Ward and Sears. UL Listed, HACR rated. 15 and 20 amp UL Listed for frequent switching applications, 120 volt AC fluorescent lighting.  1" per pole. Single-pole 1" circuit breaker features 10,000 AIR and 120/240 VAC. Uses a thermal-magnetic tripping mechanism for overload and short-circuit protection. Compatible with Homeline load centers and CSED devices. ANSI certified and UL Listed.
HomeLine HOM130C Miniature Standard Circuit Breaker HomeLine HOM120C Miniature Standard Circuit Breaker FUSE GLASS TIME DELAY 6 AMP
Single-pole 1" circuit breaker features 10,000 AIR and 120/240 VAC. Uses a thermal-magnetic tripping mechanism for overload and short-circuit protection. Compatible with Homeline load centers and CSED devices. ANSI certified and UL Listed. Single-pole 1" circuit breaker features 10,000 AIR and 120/240 VAC. Uses a thermal-magnetic tripping mechanism for overload and short-circuit protection. Compatible with Homeline load centers and CSED devices. ANSI certified and UL Listed. Glass tube. Plated brass end caps. 1/4" x 1 1/4". 250 volt AC rating maximum. UL Listed.
Eaton BR120 Type BR Miniature Circuit Breaker Eaton BR130 Type BR Miniature Circuit Breaker Eaton BR140 Type BR Miniature Circuit Breaker
Switching duty rating. Thermal magnetic 40 degrees C. Interchangeable, will replace: Bryant, Westinghouse and Challenger. Type BR. 120/240 volt, 10,000 AIR. 1" per pole. Switching duty rating. Thermal magnetic 40 degrees C. Interchangeable, will replace: Bryant, Westinghouse and Challenger. Type BR. 120/240 volt, 10,000 AIR. 1" per pole. Switching duty rating. Thermal magnetic 40 degrees C. Interchangeable, will replace: Bryant, Westinghouse and Challenger. Type BR. 120/240 volt, 10,000 AIR. 1" per pole.
Eaton BR150 Type BR Miniature Circuit Breaker MES MP120 Type MP-T Circuit Breaker Bussmann SC-20 Cartridge Low Voltage Time Delay Fuse
Switching duty rating. Thermal magnetic 40 degrees C. Interchangeable, will replace: Bryant, Westinghouse and Challenger. Type BR. 120/240 volt, 10,000 AIR. 1" per pole. One 1" space per pole. Will replace American Switch, Westinghouse Type BR, Bryant, Challenger, Sylvania, Crouse-Hinds, Murray, Frank Adams, General Electric (Full size only), General Switch, I-TE, Gould, Montgomery Ward and Sears. UL Listed, SWD rated. 120 volt AC fluorescent lighting. 120 volt AC; 10,000 AIR. High interrupting rating, current limiting. Rated at 277/480, 120/208 and 120/240 volt. UL Listed 100,000 AIR, RMS symmetrical AC (Glass G). .41 diameter fuse. Glass tube, nickel-plated brass endcaps.
MES Q115 Standard Miniature Circuit Breaker Bussmann GMA-3A Electronic Fast Acting Fuse Bussmann GMA-500MA Electronic Fast Acting Fuse
Non-interchangeable trip. 120 volt AC; 10,000 AIR. Will replace American Switch, Westinghouse Type BR, Bryant, Challenger, Sylvania, Crouse-Hinds, Murray, Frank Adams, General Electric (Full size only), General Switch, I-TE, Gould, Montgomery Ward and Sears. UL Listed, HACR rated. 15 and 20 amp UL Listed for frequent switching applications, 120 volt AC fluorescent lighting.  1" per pole. Fast acting for maximum protection. Glass tube construction. Nickel or silver-plated brass. 5mm x 20mm. UL/CSA 248-14 rated. Fast acting for maximum protection. Glass tube construction. Nickel or silver-plated brass. 5mm x 20mm. UL/CSA 248-14 rated.
Bussmann GMA-1A Electronic Fast Acting Fuse MES Q120 Standard Miniature Circuit Breaker Bussmann GMA-5A Electronic Fast Acting Fuse
Fast acting for maximum protection. Glass tube construction. Nickel or silver-plated brass. 5mm x 20mm. UL/CSA 248-14 rated. Non-interchangeable trip. 120 volt AC; 10,000 AIR. Will replace American Switch, Westinghouse Type BR, Bryant, Challenger, Sylvania, Crouse-Hinds, Murray, Frank Adams, General Electric (Full size only), General Switch, I-TE, Gould, Montgomery Ward and Sears. UL Listed, HACR rated. 15 and 20 amp UL Listed for frequent switching applications, 120 volt AC fluorescent lighting.  1" per pole. Fast acting for maximum protection. Glass tube construction. Nickel or silver-plated brass. 5mm x 20mm. UL/CSA 248-14 rated.
Bussmann GMA-2A Electronic Fast Acting Fuse FUSE TIME DELAY MEDIUM 5AMP   Bussmann TL-15 Time Delay Plug Fuse
Fast acting for maximum protection. Glass tube construction. Nickel or silver-plated brass. 5mm x 20mm. UL/CSA 248-14 rated. GMC medium time-delay glass tube fuses. UL 5x20mm. Heat absorbing metal bead on element link for time delay. Passes motor overload starting currents without needlessly opening. 125 volt maximum. Edison base. UL Listed.
Bussmann TL Time Delay Low Voltage Plug Fuse Bussmann TL Time Delay Low Voltage Plug Fuse Bussmann TL Time Delay Low Voltage Plug Fuse
Heat absorbing metal bead on element link for time delay. Passes motor overload starting currents without needlessly opening. 125 volt maximum. Edison base. UL Listed. Heat absorbing metal bead on element link for time delay. Passes motor overload starting currents without needlessly opening. 125 volt maximum. Edison base. UL Listed. Heat absorbing metal bead on element link for time delay. Passes motor overload starting currents without needlessly opening. 125 volt maximum. Edison base. UL Listed.
Bussmann GMA-250MA Cartridge Electronic Fast Acting Fuse FUSE GLASS TIME DELAY 1/2 AMP Eaton CL115 Type CL Circuit Breaker
Fast acting for maximum protection. Glass tube construction. Nickel or silver-plated brass. 5mm x 20mm. UL/CSA 248-14 rated. Glass tube. Plated brass end caps. 1/4" x 1 1/4". 250 volt AC rating maximum. UL Listed. Wire size range #14-4. Type CL replacement breakers, classified as direct replacements by Underwriters Laboratories for Square D HOMELINE, General Electric, Crouse-Hinds, Thomas & Betts, Murray and ITE/Siemens loadcenters. 120/240 volt AC, 10,000 AIC. Requires one 1-Inch (25.4 mm) space.
Eaton CL130 Type CL Circuit Breaker Eaton CL120 Type CL Circuit Breaker Bussmann GDC-5A Electronic Time Delay Fuse
Wire size range #14-4. Type CL replacement breakers, classified as direct replacements by Underwriters Laboratories for Square D HOMELINE, General Electric, Crouse-Hinds, Thomas & Betts, Murray and ITE/Siemens loadcenters. 120/240 volt AC, 10,000 AIC. Requires one 1-Inch (25.4 mm) space. Wire size range #14-4. Type CL replacement breakers, classified as direct replacements by Underwriters Laboratories for Square D HOMELINE, General Electric, Crouse-Hinds, Thomas & Betts, Murray and ITE/Siemens loadcenters. 120/240 volt AC, 10,000 AIC. Requires one 1-Inch (25.4 mm) space. Time-Delay 5 x 20mm glass tube fuse. 250 volt maximum. For electronic circuits.
FUSE TIME DELAY GLASS 15AMP   Bussmann TL-15 Time Delay Plug Fuse Bussmann TL-20 Low Voltage Time Delay Plug Fuse
Glass tube. Plated brass end caps. 1/4" x 1 1/4". 250 volt AC rating maximum. UL Listed. Heat absorbing metal bead on element link for time delay. Passes motor overload starting currents without needlessly opening. 125 volt maximum. Edison base. UL Listed. Heat absorbing metal bead on element link for time delay. Passes motor overload starting currents without needlessly opening. 125 volt maximum. Edison base. UL Listed.
Bussmann TL-25 Low Voltage Time Delay Plug Fuse Bussmann TL-30 Low Voltage Time Delay Plug Fuse Bussmann SL Time Delay Plug Fuse
Heat absorbing metal bead on element link for time delay. Passes motor overload starting currents without needlessly opening. 125 volt maximum. Edison base. UL Listed. Heat absorbing metal bead on element link for time delay. Passes motor overload starting currents without needlessly opening. 125 volt maximum. Edison base. UL Listed. Threaded fuse type, porcelain threads. Heat absorbing metal bead on element link for time delay. Passes motor overload starting currents without needlessly opening. Voltage rating of 125 volt maximum. Rejection base. UL Listed.
Bussmann SL Time Delay Plug Fuse Bussmann SL Time Delay Plug Fuse Bussmann SL Time Delay Plug Fuse
Threaded fuse type, porcelain threads. Heat absorbing metal bead on element link for time delay. Passes motor overload starting currents without needlessly opening. Voltage rating of 125 volt maximum. Rejection base. UL Listed. Threaded fuse type, porcelain threads. Heat absorbing metal bead on element link for time delay. Passes motor overload starting currents without needlessly opening. Voltage rating of 125 volt maximum. Rejection base. UL Listed. Threaded fuse type, porcelain threads. Heat absorbing metal bead on element link for time delay. Passes motor overload starting currents without needlessly opening. Voltage rating of 125 volt maximum. Rejection base. UL Listed.
Bussmann Fusetron FRN-R Cartridge Current Limiting Low Voltage Bussmann S-15 Low Voltage Tamper Proof Time Delay Plug Fuse Bussmann S-20 Low Voltage Tamper Proof Time Delay Plug Fuse
Provides motor overload, ground fault and short-circuit protection. Helps protect motors against burnout from overloads and single phasing on three phase systems. Will hold an overload which is five times greater than the ampere rating of the fuse for a minimum of ten seconds. 250 volt maximum. UL Listed, CSA Certified. Heavy duty. Protects critical motor circuits or motors that cycle on/off frequently. Body sizes prevent interchangeability and dangerous over-fusing. Dual element design, industrial/commercial grade, spring loaded to provide short circuit and overload protection. Non-transferring. Will thread into SA adaptors. UL Listed. 125 volt maximum. 10,000 AIR. Heavy duty. Protects critical motor circuits or motors that cycle on/off frequently. Body sizes prevent interchangeability and dangerous over-fusing. Dual element design, industrial/commercial grade, spring loaded to provide short circuit and overload protection. Non-transferring. Will thread into SA adaptors. UL Listed. 125 volt maximum. 10,000 AIR.
FUSE EDISON BASE PLUG HD 15AMP FUSE REJECT BASE PLUG HD 30AMP Bussmann Fusetron FRN-R Cartridge Current Limiting Low Voltage
Used for circuits where motors frequently turn on and off. A simple link element for short-circuits and dangerous overloads plus a series connected element which lets the harmless overload starting currents of motors pass without opening. Heavy duty. Protects critical motor circuits or motors that cycle on/off frequently. Body sizes prevent interchangeability and dangerous over-fusing. Dual element design, industrial/commercial grade, spring loaded to provide short circuit and overload protection. Non-transferring. Will thread into SA adaptors. UL Listed. 125 volt maximum. 10,000 AIR. Provides motor overload, ground fault and short-circuit protection. Helps protect motors against burnout from overloads and single phasing on three phase systems. Will hold an overload which is five times greater than the ampere rating of the fuse for a minimum of ten seconds. 250 volt maximum. UL Listed, CSA Certified.
Bussmann Fusetron FRN-R Cartridge Current Limiting Low Voltage Bussmann SL-15 Low Voltage Time Delay Plug Fuse Bussmann SL-20 Low Voltage Time Delay Plug Fuse
Provides motor overload, ground fault and short-circuit protection. Helps protect motors against burnout from overloads and single phasing on three phase systems. Will hold an overload which is five times greater than the ampere rating of the fuse for a minimum of ten seconds. 250 volt maximum. UL Listed, CSA Certified. Threaded fuse type, porcelain threads. Heat absorbing metal bead on element link for time delay. Passes motor overload starting currents without needlessly opening. Voltage rating of 125 volt maximum. Rejection base. UL Listed. Threaded fuse type, porcelain threads. Heat absorbing metal bead on element link for time delay. Passes motor overload starting currents without needlessly opening. Voltage rating of 125 volt maximum. Rejection base. UL Listed.
Bussmann SL-25 Time Delay Plug Fuse Bussmann SL-30 Low Voltage Time Delay Plug Fuse Bussmann T-20 Low Voltage Time Delay Plug Fuse
Threaded fuse type, porcelain threads. Heat absorbing metal bead on element link for time delay. Passes motor overload starting currents without needlessly opening. Voltage rating of 125 volt maximum. Rejection base. UL Listed. Threaded fuse type, porcelain threads. Heat absorbing metal bead on element link for time delay. Passes motor overload starting currents without needlessly opening. Voltage rating of 125 volt maximum. Rejection base. UL Listed. Used for circuits where motors frequently turn on and off. A simple link element for short-circuits and dangerous overloads plus a series connected element which lets the harmless overload starting currents of motors pass without opening.
Bussmann Fusetron FRN-R Cartridge Current Limiting Low Voltage Bussmann Fusetron FRN-R Cartridge Current Limiting Low Voltage Bussmann T-30 Low Voltage Time Delay Plug Fuse
Provides motor overload, ground fault and short-circuit protection. Helps protect motors against burnout from overloads and single phasing on three phase systems. Will hold an overload which is five times greater than the ampere rating of the fuse for a minimum of ten seconds. 250 volt maximum. UL Listed, CSA Certified. Provides motor overload, ground fault and short-circuit protection. Helps protect motors against burnout from overloads and single phasing on three phase systems. Will hold an overload which is five times greater than the ampere rating of the fuse for a minimum of ten seconds. 250 volt maximum. UL Listed, CSA Certified. Used for circuits where motors frequently turn on and off. A simple link element for short-circuits and dangerous overloads plus a series connected element which lets the harmless overload starting currents of motors pass without opening.
Bussmann T-6-1/4 Low Voltage Time Delay Plug Fuse Bussmann Fusetron FRN-R Cartridge Current Limiting Low Voltage Bussmann Fusetron FRN-R Cartridge Current Limiting Low Voltage
Used for circuits where motors frequently turn on and off. A simple link element for short-circuits and dangerous overloads plus a series connected element which lets the harmless overload starting currents of motors pass without opening. Provides motor overload, ground fault and short-circuit protection. Helps protect motors against burnout from overloads and single phasing on three phase systems. Will hold an overload which is five times greater than the ampere rating of the fuse for a minimum of ten seconds. 250 volt maximum. UL Listed, CSA Certified. Provides motor overload, ground fault and short-circuit protection. Helps protect motors against burnout from overloads and single phasing on three phase systems. Will hold an overload which is five times greater than the ampere rating of the fuse for a minimum of ten seconds. 250 volt maximum. UL Listed, CSA Certified.
Bussmann Fusetron FRN-R Cartridge Current Limiting Low Voltage Bussmann Fusetron FRN-R Cartridge Current Limiting Low Voltage Bussmann Fusetron FRN-R Cartridge Current Limiting Low Voltage
Provides motor overload, ground fault and short-circuit protection. Helps protect motors against burnout from overloads and single phasing on three phase systems. Will hold an overload which is five times greater than the ampere rating of the fuse for a minimum of ten seconds. 250 volt maximum. UL Listed, CSA Certified. Provides motor overload, ground fault and short-circuit protection. Helps protect motors against burnout from overloads and single phasing on three phase systems. Will hold an overload which is five times greater than the ampere rating of the fuse for a minimum of ten seconds. 250 volt maximum. UL Listed, CSA Certified. Provides motor overload, ground fault and short-circuit protection. Helps protect motors against burnout from overloads and single phasing on three phase systems. Will hold an overload which is five times greater than the ampere rating of the fuse for a minimum of ten seconds. 250 volt maximum. UL Listed, CSA Certified.
Cooper Wiring NO.263 Fuse Reducer Bussmann S-6-1/4 Low Voltage Time Delay Plug Fuse Bussmann S-8 Low Voltage Tamper Proof Time Delay Plug Fuse
Fuse reducers allow a smaller size fuse to be installed in a fuse block intended for a larger fuse. A No.263 reducer installed on a 30 amp fuse permits it to be installed in a 60 amp fuse block. Reducers are particularly useful when equipment is being converted. Proper protection can be maintained without the expense of replacing the fuse block. Heavy duty. Protects critical motor circuits or motors that cycle on/off frequently. Body sizes prevent interchangeability and dangerous over-fusing. Dual element design, industrial/commercial grade, spring loaded to provide short circuit and overload protection. Non-transferring. Will thread into SA adaptors. UL Listed. 125 volt maximum. 10,000 AIR. Heavy duty. Protects critical motor circuits or motors that cycle on/off frequently. Body sizes prevent interchangeability and dangerous over-fusing. Dual element design, industrial/commercial grade, spring loaded to provide short circuit and overload protection. Non-transferring. Will thread into SA adaptors. UL Listed. 125 volt maximum. 10,000 AIR.
Bussmann S-10 Low Voltage Time Delay Plug Fuse GE THQL2120 Type THQL Q-Line Standard Circuit Breaker GE THQL2130 Type THQL Q-Line Standard Circuit Breaker
Heavy duty. Protects critical motor circuits or motors that cycle on/off frequently. Body sizes prevent interchangeability and dangerous over-fusing. Dual element design, industrial/commercial grade, spring loaded to provide short circuit and overload protection. Non-transferring. Will thread into SA adaptors. UL Listed. 125 volt maximum. 10,000 AIR. Copper-to-copper connections, calibrated for optimum trip performance, heat resistant thermoset cases and covers, cemented calibration screw. May be used, when marked to accept, with American Switch, Arrow Hart, Bryant, General Switch, GTE, Sylvania, most ITE, Murray, Westinghouse Type BR, Challenger, Crouse-Hinds. 15 to 30 amp 14 - 8 Cu or 12 - 8 Al AWG wire, 35 to 60 amp 8 - 3 Cu or 8 - 2 Al AWG wire, 70 to 100 amp 6-1/0 Cu or 4 - 1/0 Al AWG wire. UL Listed, HACR rated. 120/240 volt; 10,000 AIR.  1" per pole (2" total). Copper-to-copper connections, calibrated for optimum trip performance, heat resistant thermoset cases and covers, cemented calibration screw. May be used, when marked to accept, with American Switch, Arrow Hart, Bryant, General Switch, GTE, Sylvania, most ITE, Murray, Westinghouse Type BR, Challenger, Crouse-Hinds. 15 to 30 amp 14 - 8 Cu or 12 - 8 Al AWG wire, 35 to 60 amp 8 - 3 Cu or 8 - 2 Al AWG wire, 70 to 100 amp 6-1/0 Cu or 4 - 1/0 Al AWG wire. UL Listed, HACR rated. 120/240 volt; 10,000 AIR.  1" per pole (2" total).
GE THQL2140 Type THQL Q-Line Standard Circuit Breaker GE THQL2150 Type THQL Q-Line Standard Circuit Breaker GE THQL2160 Type THQL Q-Line Standard Circuit Breaker
Copper-to-copper connections, calibrated for optimum trip performance, heat resistant thermoset cases and covers, cemented calibration screw. May be used, when marked to accept, with American Switch, Arrow Hart, Bryant, General Switch, GTE, Sylvania, most ITE, Murray, Westinghouse Type BR, Challenger, Crouse-Hinds. 15 to 30 amp 14 - 8 Cu or 12 - 8 Al AWG wire, 35 to 60 amp 8 - 3 Cu or 8 - 2 Al AWG wire, 70 to 100 amp 6-1/0 Cu or 4 - 1/0 Al AWG wire. UL Listed, HACR rated. 120/240 volt; 10,000 AIR.  1" per pole (2" total). Copper-to-copper connections, calibrated for optimum trip performance, heat resistant thermoset cases and covers, cemented calibration screw. May be used, when marked to accept, with American Switch, Arrow Hart, Bryant, General Switch, GTE, Sylvania, most ITE, Murray, Westinghouse Type BR, Challenger, Crouse-Hinds. 15 to 30 amp 14 - 8 Cu or 12 - 8 Al AWG wire, 35 to 60 amp 8 - 3 Cu or 8 - 2 Al AWG wire, 70 to 100 amp 6-1/0 Cu or 4 - 1/0 Al AWG wire. UL Listed, HACR rated. 120/240 volt; 10,000 AIR.  1" per pole (2" total). Copper-to-copper connections, calibrated for optimum trip performance, heat resistant thermoset cases and covers, cemented calibration screw. May be used, when marked to accept, with American Switch, Arrow Hart, Bryant, General Switch, GTE, Sylvania, most ITE, Murray, Westinghouse Type BR, Challenger, Crouse-Hinds. 15 to 30 amp 14 - 8 Cu or 12 - 8 Al AWG wire, 35 to 60 amp 8 - 3 Cu or 8 - 2 Al AWG wire, 70 to 100 amp 6-1/0 Cu or 4 - 1/0 Al AWG wire. UL Listed, HACR rated. 120/240 volt; 10,000 AIR.  1" per pole (2" total).
GE THQP250 Type THQP Q-Line Thin Miniature Circuit Breaker GE THQP240 Type THQP Q-Line Standard Circuit Breaker GE THQP230 Type THQP Q-Line Standard Circuit Breaker
Copper-to-copper connections, calibrated for optimum trip performance, heat resistant thermoset cases and covers, cemented calibration screw. Nearly identical to Type THQL with the same design and performance, yet only taking up 1/2 the space. 1/2" per pole. UL Listed, HACR rated. 15 to 25 amp 14 - 8 Cu or 12 - 8 Al AWG wire, 30 to 50 amp 8 - 4 Cu or 8 - 2 Al AWG wire. 3-9/32" height x 1/2" width x 2-3/8" depth. 120/240 volt; 10,000 AIR. Copper-to-copper connections, calibrated for optimum trip performance, heat resistant thermoset cases and covers, cemented calibration screw. Nearly identical to Type THQL with the same design and performance, yet only taking up 1/2 the space. 1/2" per pole. UL Listed, HACR rated. 15 to 25 amp 14 - 8 Cu or 12 - 8 Al AWG wire, 30 to 50 amp 8 - 4 Cu or 8 - 2 Al AWG wire. 3-9/32" height x 1/2" width x 2-3/8" depth. 120/240 volt; 10,000 AIR. Copper-to-copper connections, calibrated for optimum trip performance, heat resistant thermoset cases and covers, cemented calibration screw. Nearly identical to Type THQL with the same design and performance, yet only taking up 1/2 the space. 1/2" per pole. UL Listed, HACR rated. 15 to 25 amp 14 - 8 Cu or 12 - 8 Al AWG wire, 30 to 50 amp 8 - 4 Cu or 8 - 2 Al AWG wire. 3-9/32" height x 1/2" width x 2-3/8" depth. 120/240 volt; 10,000 AIR.
GE THQP220 Type THQP Q-Line Miniature Circuit Breaker Square D QO140CP Type QO Standard Circuit Breaker Square D QO150CP Type QO Standard Circuit Breaker
Copper-to-copper connections, calibrated for optimum trip performance, heat resistant thermoset cases and covers, cemented calibration screw. Nearly identical to Type THQL with the same design and performance, yet only taking up 1/2 the space. 1/2" per pole. UL Listed, HACR rated. 15 to 25 amp 14 - 8 Cu or 12 - 8 Al AWG wire, 30 to 50 amp 8 - 4 Cu or 8 - 2 Al AWG wire. 3-9/32" height x 1/2" width x 2-3/8" depth. 120/240 volt; 10,000 AIR. Single-pole 3/4" circuit breaker provides overload and short circuit protection. Features a red Visi-Trip indicator to identify a tripped breaker. Accepts aluminum or copper conductors. Rated for 120/240Vac and at 10,000 Ampre Interrupting Rating (AIR). CSA approved to only install in Canadian Square D loadcentres. Single-pole 3/4" circuit breaker provides overload and short circuit protection. Features a red Visi-Trip indicator to identify a tripped breaker. Accepts aluminum or copper conductors. Rated for 120/240Vac and at 10,000 Ampre Interrupting Rating (AIR). CSA approved to only install in Canadian Square D loadcentres.
Bussmann T Time Delay Plug Fuse Square D QO115CP Type QO Standard Circuit Breaker Square D QO120CP Type QO Standard Circuit Breaker
Used for circuits where motors frequently turn on and off. A simple link element for short-circuits and dangerous overloads plus a series connected element which lets the harmless overload starting currents of motors pass without opening. Single-pole 3/4" circuit breaker provides overload and short circuit protection. Features a red Visi-Trip indicator to identify a tripped breaker. Accepts aluminum or copper conductors. Rated for 120/240Vac and at 10,000 Ampre Interrupting Rating (AIR). CSA approved to only install in Canadian Square D loadcentres. Single-pole 3/4" circuit breaker provides overload and short circuit protection. Features a red Visi-Trip indicator to identify a tripped breaker. Accepts aluminum or copper conductors. Rated for 120/240Vac and at 10,000 Ampre Interrupting Rating (AIR). CSA approved to only install in Canadian Square D loadcentres.
Square D QO130CP Type QO Standard Circuit Breaker HomeLine HOM215CP Standard Circuit Breaker HomeLine HOM230CP Standard Circuit Breaker
Single-pole 3/4" circuit breaker provides overload and short circuit protection. Features a red Visi-Trip indicator to identify a tripped breaker. Accepts aluminum or copper conductors. Rated for 120/240Vac and at 10,000 Ampre Interrupting Rating (AIR). CSA approved to only install in Canadian Square D loadcentres. Double pole 2" circuit breaker features 10,000 AIR and 120/240 VAC. Thermal-magnetic tripping mechanism for overload and short-circuit protection of electrical system. Accepts aluminum or copper conductors. CSA approved to only install in Canadian HomeLine loadcentres. Double pole 2" circuit breaker features 10,000 AIR and 120/240 VAC. Thermal-magnetic tripping mechanism for overload and short-circuit protection of electrical system. Accepts aluminum or copper conductors. CSA approved to only install in Canadian HomeLine loadcentres.
HomeLine HOM240CP Standard Circuit Breaker HomeLine HOM250CP Standard Circuit Breaker HomeLine HOM260CP Standard Circuit Breaker
Double pole 2" circuit breaker features 10,000 AIR and 120/240 VAC. Thermal-magnetic tripping mechanism for overload and short-circuit protection of electrical system. Accepts aluminum or copper conductors. CSA approved to only install in Canadian HomeLine loadcentres. Double pole 2" circuit breaker features 10,000 AIR and 120/240 VAC. Thermal-magnetic tripping mechanism for overload and short-circuit protection of electrical system. Accepts aluminum or copper conductors. CSA approved to only install in Canadian HomeLine loadcentres. Double pole 2" circuit breaker features 10,000 AIR and 120/240 VAC. Thermal-magnetic tripping mechanism for overload and short-circuit protection of electrical system. Accepts aluminum or copper conductors. CSA approved to only install in Canadian HomeLine loadcentres.
HomeLine HOM220CP Standard Circuit Breaker Square D QO115C Miniature Standard Circuit Breaker Square D QO120C Miniature Standard Circuit Breaker
Double pole 2" circuit breaker features 10,000 AIR and 120/240 VAC. Thermal-magnetic tripping mechanism for overload and short-circuit protection of electrical system. Accepts aluminum or copper conductors. CSA approved to only install in Canadian HomeLine loadcentres. Single-pole 3/4" circuit breaker provides overload and short circuit protection. Features a red Visi-Trip indicator to identify a tripped breaker. Accepts aluminum or copper conductors. Rated for 120/240Vac and at 10,000 Ampre Interrupting Rating (AIR). CSA approved to only install in Canadian Square D loadcentres. Single-pole 3/4" circuit breaker provides overload and short circuit protection. Features a red Visi-Trip indicator to identify a tripped breaker. Accepts aluminum or copper conductors. Rated for 120/240Vac and at 10,000 Ampre Interrupting Rating (AIR). CSA approved to only install in Canadian Square D loadcentres.
Square D QO130C Miniature Standard Circuit Breaker Bussmann Fusetron T-10 Low Voltage Time Delay Plug Fuse FUSE FNM MIDGET T-DELAY 20AMP
Single-pole 3/4" circuit breaker provides overload and short circuit protection. Features a red Visi-Trip indicator to identify a tripped breaker. Accepts aluminum or copper conductors. Rated for 120/240Vac and at 10,000 Ampre Interrupting Rating (AIR). CSA approved to only install in Canadian Square D loadcentres. Used for circuits where motors frequently turn on and off. A simple link element for short-circuits and dangerous overloads plus a series connected element which lets the harmless overload starting currents of motors pass without opening. Provides supplemental protection to industrial, commercial, agricultural, heating, ventilating and air conditioning equipment. Used to protect internal components such as control circuit wiring, motor control transformers and small motors. 250 volt maximum, 13/32" x 1-1/2".
FUSE FNM MIDGET T-DELAY 30AMP FUSE FNM MIDGET T-DELAY 10AMP ADAPTER FUSE PLUG 7-15 AMP
Provides supplemental protection to industrial, commercial, agricultural, heating, ventilating and air conditioning equipment. Used to protect internal components such as control circuit wiring, motor control transformers and small motors. 250 volt maximum, 13/32" x 1-1/2". Provides supplemental protection to industrial, commercial, agricultural, heating, ventilating and air conditioning equipment. Used to protect internal components such as control circuit wiring, motor control transformers and small motors. 250 volt maximum, 13/32" x 1-1/2". Fustat adapters for using S and SL rejection plug fuses in Edison base sockets. Converts Edison base receptacles to accept a rejection base fuse.
Bussmann MB Plug Fuse Bussmann Fusetron NON-100 Cartridge Bussmann VPKMB-20 Manual Reset Plug Fuse
Plug-type circuit breaker. For use with plug fuse panels. For general purpose circuits, protects lighting, heating and other circuits not subject to temporary surges and where available short-circuit currents are relatively low. Does not have any appreciable degree of time delay and should not be specified in circuits where large transients or motor overloads occur. Single element type. The counterpart of type W plug fuses. Use in non-motor circuits. 50,000 AIR. 250 volt maximum. UL Listed. Plug-type circuit breaker. For use with plug fuse panels.
HomeLine HOMT2020CP Tandem Twin Circuit Breaker HomeLine HOMT1515CP Tandem Circuit Breaker MES Q220 Standard Miniature Circuit Breaker
Tandem 1" single-pole circuit breaker. Offers 2 circuits in the space of 1. Features 10,000 AIR and 120/240 VAC. Thermal-magnetic tripping mechanism for overload and short-circuit protection of the electrical system. Accepts aluminum or copper conductors. CSA approved to only install in Canadian HomeLine loadcentres. Tandem 1" single-pole circuit breaker. Offers 2 circuits in the space of 1. Features 10,000 AIR and 120/240 VAC. Thermal-magnetic tripping mechanism for overload and short-circuit protection of the electrical system. Accepts aluminum or copper conductors. CSA approved to only install in Canadian HomeLine loadcentres. Molded case with non-interchangeable trip. Will replace American Switch, Westinghouse Type BR, Bryant, Challenger, Sylvania, Crouse-Hinds, Murray, Frank Adams, General Electric (Full size only), General Switch, I-T-E, Gould, Montgomery Ward and Sears. UL Listed. HACR rated. 120/240 volt AC; 10,000 AIR. 1" per pole (2" total).
MES Q230 Standard Miniature Circuit Breaker MES Q240 Standard Miniature Circuit Breaker MES Q250 Standard Miniature Circuit Breaker
Molded case with non-interchangeable trip. Will replace American Switch, Westinghouse Type BR, Bryant, Challenger, Sylvania, Crouse-Hinds, Murray, Frank Adams, General Electric (Full size only), General Switch, I-T-E, Gould, Montgomery Ward and Sears. UL Listed. HACR rated. 120/240 volt AC; 10,000 AIR. 1" per pole (2" total). Molded case with non-interchangeable trip. Will replace American Switch, Westinghouse Type BR, Bryant, Challenger, Sylvania, Crouse-Hinds, Murray, Frank Adams, General Electric (Full size only), General Switch, I-T-E, Gould, Montgomery Ward and Sears. UL Listed. HACR rated. 120/240 volt AC; 10,000 AIR. 1" per pole (2" total). Molded case with non-interchangeable trip. Will replace American Switch, Westinghouse Type BR, Bryant, Challenger, Sylvania, Crouse-Hinds, Murray, Frank Adams, General Electric (Full size only), General Switch, I-T-E, Gould, Montgomery Ward and Sears. UL Listed. HACR rated. 120/240 volt AC; 10,000 AIR. 1" per pole (2" total).
MES Q260 Standard Miniature Circuit Breaker HomeLine HOM250C Miniature Standard Circuit Breaker HomeLine HOM260C Miniature Standard Circuit Breaker
Molded case with non-interchangeable trip. Will replace American Switch, Westinghouse Type BR, Bryant, Challenger, Sylvania, Crouse-Hinds, Murray, Frank Adams, General Electric (Full size only), General Switch, I-T-E, Gould, Montgomery Ward and Sears. UL Listed. HACR rated. 120/240 volt AC; 10,000 AIR. 1" per pole (2" total). Double pole 2" circuit breaker features 10,000 AIR and 120/240 VAC. Thermal-magnetic tripping mechanism for overload and short-circuit protection of electrical system. Accepts aluminum or copper conductors. CSA approved to only install in Canadian HomeLine loadcentres. Double pole 2" circuit breaker features 10,000 AIR and 120/240 VAC. Thermal-magnetic tripping mechanism for overload and short-circuit protection of electrical system. Accepts aluminum or copper conductors. CSA approved to only install in Canadian HomeLine loadcentres.
HomeLine HOM240C Miniature Standard Circuit Breaker HomeLine HOM220C Miniature Standard Circuit Breaker HomeLine HOM230C Miniature Standard Circuit Breaker
Double pole 2" circuit breaker features 10,000 AIR and 120/240 VAC. Thermal-magnetic tripping mechanism for overload and short-circuit protection of electrical system. Accepts aluminum or copper conductors. CSA approved to only install in Canadian HomeLine loadcentres. Double pole 2" circuit breaker features 10,000 AIR and 120/240 VAC. Thermal-magnetic tripping mechanism for overload and short-circuit protection of electrical system. Accepts aluminum or copper conductors. CSA approved to only install in Canadian HomeLine loadcentres. Double pole 2" circuit breaker features 10,000 AIR and 120/240 VAC. Thermal-magnetic tripping mechanism for overload and short-circuit protection of electrical system. Accepts aluminum or copper conductors. CSA approved to only install in Canadian HomeLine loadcentres.
ADAPTER FUSE PLUG 20 AMP      MES MP250 Type MP-T Circuit Breaker Eaton BR215 Type BR Miniature Circuit Breaker
Fustat adapters for using S and SL rejection plug fuses in Edison base sockets. Converts Edison base receptacles to accept a rejection base fuse. UL Listed; 120/240 volt. Common trip. Requires one 2" space. Interchangeable, will replace: Bryant, Challenger and Westinghouse. Type BR. 120/240 volt. 10 kAIC, 10,000 AIR. 2 spaces, 2" per breaker.
   
 
1 2 3