Home > ELECTRICAL > ROUGH ELECTRICAL > OUTDOOR BOXES & LAMPHOLDERS
Sort By:
1 2
Bell Raco 5173-2 Blank Weatherproof Device Cover Bell Raco 5173-1 Blank Weatherproof Device Cover Bell 5019-0 Replacement Rectangular Multipurpose Gasket
Outdoor use, rugged metallic construction. Powder coat finish. Scratch resistant. Includes installation hardware, gasket, and multi-lingual instructions. C/UL/US UL Listed. NEMA 3R rated. Outdoor use, rugged metallic construction. Powder coat finish. Scratch resistant. Includes installation hardware, gasket, and multi-lingual instructions. C/UL/US UL Listed. NEMA 3R rated. Rectangular replacement gaskets for weatherproof covers and lamp holders. Each gasket has cut outs for a toggle switch, duplex receptacle and 1.406" diameter round receptacle. Remove the cut outs for the duplex and round receptacles for a GFCI receptacle opening.
Hubbell 5173-5 Blank Weatherproof Cover Hubbell 5173-6 Blank Weatherproof Cover Bell 5269-5 Closure Plug
Outdoor use, rugged metallic construction. Powder coat finish. Scratch resistant. Includes installation hardware, gasket, and multi-lingual instructions. C/UL/US UL Listed. NEMA 3R rated. Outdoor use, rugged metallic construction. Powder coat finish. Scratch resistant. Includes installation hardware, gasket, and multi-lingual instructions. C/UL/US UL Listed. NEMA 3R rated. For use with weatherproof boxes, extension adapters, cluster covers and round splice boxes to seal off unused outlets.
Bell 5269-7 Closure Plug Bell 5269-6 Closure Plug Bell 5269-1 Closure Plug
For use with weatherproof boxes, extension adapters, cluster covers and round splice boxes to seal off unused outlets. For use with weatherproof boxes, extension adapters, cluster covers and round splice boxes to seal off unused outlets. For use with weatherproof boxes, extension adapters, cluster covers and round splice boxes to seal off unused outlets.
Bell 5270-5 Closure Plug Bell 5269-0 Closure Plug Hubbell 5374-0 Blank Round Flat Weatherproof Cover
For use with weatherproof boxes, extension adapters, cluster covers and round splice boxes to seal off unused outlets. For use with weatherproof boxes, extension adapters, cluster covers and round splice boxes to seal off unused outlets. For use with 4" round splice boxes. Installation hardware, and gasket included. 4" diameter, shrink wrapped. UL Listed.
Arrow Hart S2962 Weatherproof Cover Bell Raco 5175-1 Blank Weatherproof Device Cover Hubbell 5193-0 3-Hole Cluster Lampholder Cover
Tough plastic construction, resistant to high impact and sunlight. Non-corrosive and non-conductive. Gasket provided seals both device openings and edges. Self closing cover. Vertical only. UL Listed for wet locations with cover closed. For use whenever weatherproof protection is required for a weatherproof box. Rugged die cast construction. Powder coat finish provides scratch resistance. Includes gasket and mounting hardware. Multi-lingual instructions in each package. UL Listed, NEMA 3R Rated. 4-1/2" x 4-1/2". For wet locations. Gasket, screws and plugs included. 4" cluster cover. Use 75-150 watt maximum, Die cast zinc. One 1/2" NPT hole. UL Listed.
Bell Raco 5193-1 Round Cluster Cover Hubbell 5175-5 Blank Weatherproof Cover Hubbell 5186-0 1-Hole Cluster Lampholder Cover
For wet locations. Gasket, screws and plugs included. 4" cluster cover. Use 75-150 watt maximum, Die cast zinc. One 1/2" NPT hole. UL Listed. For use whenever weatherproof protection is required for a weatherproof box. Rugged die cast construction. Powder coat finish provides scratch resistance. Includes gasket and mounting hardware. Multi-lingual instructions in each package. UL Listed, NEMA 3R Rated. 4-1/2" x 4-1/2". For wet locations. Gasket, screws and plugs included. Use 75-150 watt maximum, Par-38 lamps. Die cast zinc, powder coat finish provides maximum weatherability and scratch resistance. Includes installation hardware, gasket, and multi-lingual instructions. One 1/2" NPT hole. Underwriters Recognized Component CSA C22.2 No. 18 NEMA 3R Rated.
Hubbell 5180-0 Weatherproof Device Cover Bell Raco 5186 Rectangular Cluster Cover Hubbell 5180-6 Weatherproof Device Cover
Horizontal device mount. Weatherproof covers for protection of outdoor receptacles. State-of-the-art powder coat finish provides maximum weatherability and scratch resistance. Self-closing lids assure weatherproof protection when the receptacle is not in use. Includes installation hardware, gasket, and multi-lingual instructions. Size: 4-1/2" x 2-3/4". UL 514-A listed, File E195978 CSA C22.2 No. 18 NEMA 3R Rated. For wet locations. Gasket, screws and plugs included. Use 75-150 watt maximum, Par-38 lamps. Die cast zinc, powder coat finish provides maximum weatherability and scratch resistance. Includes installation hardware, gasket, and multi-lingual instructions. One 1/2" NPT hole. Underwriters Recognized Component CSA C22.2 No. 18 NEMA 3R Rated. Horizontal device mount. Weatherproof covers for protection of outdoor receptacles. State-of-the-art powder coat finish provides maximum weatherability and scratch resistance. Self-closing lids assure weatherproof protection when the receptacle is not in use. Includes installation hardware, gasket, and multi-lingual instructions. Size: 4-1/2" x 2-3/4". UL 514-A listed, File E195978 CSA C22.2 No. 18 NEMA 3R Rated.
Bell Raco 5180-1 2-Hole Weatherproof Device Cover Arrow Hart S1962 Utility Halogen Low Profile Weatherproof Cover Arrow Hart S1962W-SP Weatherproof Cover
Horizontal device mount. Weatherproof covers for protection of outdoor receptacles. State-of-the-art powder coat finish provides maximum weatherability and scratch resistance. Self-closing lids assure weatherproof protection when the receptacle is not in use. Includes installation hardware, gasket, and multi-lingual instructions. Size: 4-1/2" x 2-3/4". UL 514-A listed, File E195978 CSA C22.2 No. 18 NEMA 3R Rated. Tough plastic construction, resistant to high impact and sunlight. Non-metallic, non-corrosive and non-conductive. Gasket provided seals both device openings and edges. UL Listed for damp locations. Stay open lids. Size 2-3/4" x 4-1/2". Tough plastic construction, resistant to high impact and sunlight. Non-metallic, non-corrosive and non-conductive. Gasket provided seals both device openings and edges. UL Listed for damp locations. Stay open lids. Size 2-3/4" x 4-1/2".
Bell Raco 5197-2 Round Cluster Cover Bell Raco 5189 Rectangular Cluster Cover Bell Raco 5189 Rectangular Cluster Cover
For wet locations. Gasket, screws and plugs included. 4" cluster cover. Die cast zinc. Three 1/2" NPT holes. UL Listed. Includes installation hardware, gasket, and multi-lingual instructions. 3 hole covers are supplied with two closure plugs. Die cast zinc construction. Three 1/2" NPT holes. UR - Underwrites recognized component CSA C22.2 No. 18 compliant. Includes installation hardware, gasket, and multi-lingual instructions. 3 hole covers are supplied with two closure plugs. Die cast zinc construction. Three 1/2" NPT holes. UR - Underwrites recognized component CSA C22.2 No. 18 compliant.
Arrow Hart S1961W-SP Weatherproof Cover Hubbell 5197-0 3-Hole Cluster Lampholder Cover Arrow Hart S1961 Weatherproof Cover
Resistant to high impact and sunlight. Non-metallic, non-corrosive and non-conductive. Gasket provided seals both device openings and edges. Lid stays open in use. UL Listed for damp locations. For wet locations. Gasket, screws and plugs included. 4" cluster cover. Die cast zinc. Three 1/2" NPT holes. UL Listed. Resistant to high impact and sunlight. Non-metallic, non-corrosive and non-conductive. Gasket provided seals both device openings and edges. Lid stays open in use. UL Listed for damp locations.
Hubbell 5189-0 3-Hole Cluster Lampholder Cover Hubbell 5320-0 Outlet Box Bell Raco 5193-5 Round Cluster Cover
Includes installation hardware, gasket, and multi-lingual instructions. 3 hole covers are supplied with two closure plugs. Die cast zinc construction. Three 1/2" NPT holes. UR - Underwrites recognized component CSA C22.2 No. 18 compliant. For use in wet, damp or dry locations. Three 1/2" threaded outlets. 2" deep with lugs. May be used as a weatherproof junction box, or as a housing for receptacles, switches, and GFCIs. Powder coat finish. Eight box mounting options with detachable lugs provided. Includes two closure plugs. Ground screw installed. Multi-lingual instructions. Internal threads and hubs comply with NEMA requirements. Hubs accept all threaded fittings and threaded conduit. Die cast aluminum construction. 18.3 cubic inch capacity. 2" depth x 4-1/2" length x 2-3/4" width. UL Listed. NEMA 3R rated. For wet locations. Gasket, screws and plugs included. 4" cluster cover. Use 75-150 watt maximum, Die cast zinc. One 1/2" NPT hole. UL Listed.
Bell Raco 5320-1 Weatherproof Box Bell Raco 5175-0 Blank Weatherproof Device Cover Bell Raco 5197-1 Round Cluster Cover
For use in wet, damp or dry locations. Three 1/2" threaded outlets. 2" deep with lugs. May be used as a weatherproof junction box, or as a housing for receptacles, switches, and GFCIs. Powder coat finish. Eight box mounting options with detachable lugs provided. Includes two closure plugs. Ground screw installed. Multi-lingual instructions. Internal threads and hubs comply with NEMA requirements. Hubs accept all threaded fittings and threaded conduit. Die cast aluminum construction. 18.3 cubic inch capacity. 2" depth x 4-1/2" length x 2-3/4" width. UL Listed. NEMA 3R rated. For use whenever weatherproof protection is required for a weatherproof box. Rugged die cast construction. Powder coat finish provides scratch resistance. Includes gasket and mounting hardware. Multi-lingual instructions in each package. UL Listed, NEMA 3R Rated. 4-1/2" x 4-1/2". For wet locations. Gasket, screws and plugs included. 4" cluster cover. Die cast zinc. Three 1/2" NPT holes. UL Listed.
Bell Raco 5180-2 2-Hole Weatherproof Device Cover Bell Raco 5193-6 Round Cluster Cover Bell Raco 5606 Lampholder
Horizontal device mount. Weatherproof covers for protection of outdoor receptacles. State-of-the-art powder coat finish provides maximum weatherability and scratch resistance. Self-closing lids assure weatherproof protection when the receptacle is not in use. Includes installation hardware, gasket, and multi-lingual instructions. Size: 4-1/2" x 2-3/4". UL 514-A listed, File E195978 CSA C22.2 No. 18 NEMA 3R Rated. For wet locations. Gasket, screws and plugs included. 4" cluster cover. Use 75-150 watt maximum, Die cast zinc. One 1/2" NPT hole. UL Listed. Die cast zinc with porcelain socket. For wet locations. Use 75-150 watt maximum, Par-38 lamps. Includes gaskets and locknuts. UL Listed.
Bell Raco 5180-7 2-Hole Weatherproof Device Cover Bell Raco 5606 Lampholder Hubbell 5606 Adjustable Weatherproof Lampholder
Horizontal device mount. Weatherproof covers for protection of outdoor receptacles. State-of-the-art powder coat finish provides maximum weatherability and scratch resistance. Self-closing lids assure weatherproof protection when the receptacle is not in use. Includes installation hardware, gasket, and multi-lingual instructions. Size: 4-1/2" x 2-3/4". UL 514-A listed, File E195978 CSA C22.2 No. 18 NEMA 3R Rated. Die cast zinc with porcelain socket. For wet locations. Use 75-150 watt maximum, Par-38 lamps. Includes gaskets and locknuts. UL Listed. Die cast zinc with porcelain socket. For wet locations. Use 75-150 watt maximum, Par-38 lamps. Includes gaskets and locknuts. UL Listed.
Hubbell 5180-5 Weatherproof Device Cover Bell Raco 5406-0 Weatherproof Extension Box Bell Raco 5320-2 Weatherproof Box
Horizontal device mount. Weatherproof covers for protection of outdoor receptacles. State-of-the-art powder coat finish provides maximum weatherability and scratch resistance. Self-closing lids assure weatherproof protection when the receptacle is not in use. Includes installation hardware, gasket, and multi-lingual instructions. Size: 4-1/2" x 2-3/4". UL 514-A listed, File E195978 CSA C22.2 No. 18 NEMA 3R Rated. Used to provide additional capacity. Die cast aluminum construction. Installation hardware, gasket, and ground screw provided. 9.5 cubic inch capacity. 4-1/2" x 2-3/4" x 1" deep. UL Listed, CSA, NEMA 3R Rated. For use in wet, damp or dry locations. Three 1/2" threaded outlets. 2" deep with lugs. May be used as a weatherproof junction box, or as a housing for receptacles, switches, and GFCIs. Powder coat finish. Eight box mounting options with detachable lugs provided. Includes two closure plugs. Ground screw installed. Multi-lingual instructions. Internal threads and hubs comply with NEMA requirements. Hubs accept all threaded fittings and threaded conduit. Die cast aluminum construction. 18.3 cubic inch capacity. 2" depth x 4-1/2" length x 2-3/4" width. UL Listed. NEMA 3R rated.
Bell Raco 5152-0 Weatherproof Device Cover Hubbell 5155-5 Single Device Cover Bell Raco 5189 Rectangular Cluster Cover
State-of-the-art powder coat finish provides maximum weatherability and scratch resistance. Self-closing lids assure weatherproof protection when the receptacle is not in use. Installation hardware, gasket, multi-lingual instructions included. For single 1.406" diameter receptacle. UL Listed for wet location with cover closed. With powder coat finish for weatherability and scratch resistance. For use whenever weatherproof protection is required for an outdoor receptacle. Self-closing lid for weatherproof protection when the receptacle is not in use. Includes installation hardware, gasket, and multi-lingual instructions. Size: 4-1/2" length x 2-3/4" width x 1.406" depth. UL Listed, Meets Standard 514A, C22.2 No. 18, (5103 series) NEMA 3R rated. Includes installation hardware, gasket, and multi-lingual instructions. 3 hole covers are supplied with two closure plugs. Die cast zinc construction. Three 1/2" NPT holes. UR - Underwrites recognized component CSA C22.2 No. 18 compliant.
Bell Raco 5197-5 Round Cluster Cover Bell Raco 5606 Lampholder Hubbell 5320-6 Outlet Box
For wet locations. Gasket, screws and plugs included. 4" cluster cover. Die cast zinc. Three 1/2" NPT holes. UL Listed. Die cast zinc with porcelain socket. For wet locations. Use 75-150 watt maximum, Par-38 lamps. Includes gaskets and locknuts. UL Listed. For use in wet, damp or dry locations. Three 1/2" threaded outlets. 2" deep with lugs. May be used as a weatherproof junction box, or as a housing for receptacles, switches, and GFCIs. Powder coat finish. Eight box mounting options with detachable lugs provided. Includes two closure plugs. Ground screw installed. Multi-lingual instructions. Internal threads and hubs comply with NEMA requirements. Hubs accept all threaded fittings and threaded conduit. Die cast aluminum construction. 18.3 cubic inch capacity. 2" depth x 4-1/2" length x 2-3/4" width. UL Listed. NEMA 3R rated.
Hubbell 5189-6 3-Hole Cluster Lampholder Cover Hubbell 5197-6 3-Hole Cluster Lampholder Cover Hubbell 5606 Adjustable Weatherproof Lampholder
Includes installation hardware, gasket, and multi-lingual instructions. 3 hole covers are supplied with two closure plugs. Die cast zinc construction. Three 1/2" NPT holes. UR - Underwrites recognized component CSA C22.2 No. 18 compliant. For wet locations. Gasket, screws and plugs included. 4" cluster cover. Die cast zinc. Three 1/2" NPT holes. UL Listed. Die cast zinc with porcelain socket. For wet locations. Use 75-150 watt maximum, Par-38 lamps. Includes gaskets and locknuts. UL Listed.
Raco 2011FBAR Vapor Barrier Box Carlon E98TSCN-CAR Weatherproof Device Cover Hubbell 5324-0 Outlet Box
Made from rugged polycarbonate material, yellow color, gasket seals all openings to prevent air or vapor penetration. Front-mounted ground screw, 1/2" setback, flush bracket. Self-clamping, nonmetallic sheathed cable entry tabs. Weatherproof cover for single toggle switch applications. Vertical mount. UV resistant, suitable for outdoor use. Nonmetallic/noncorrosive, won't rust or fade, paintable. UL Marine Listed, CSA Certified. With lugs. Die cast aluminum. For use in branch circuit wiring in wet, damp, or dry locations. May be used as a weatherproof junction box, or as housing for receptacles, switches, and GFCI's. Eight box mounting options with detachable lugs provided. Three threaded 3/4" outlets. Powder coat finish. 18.3 cubic inch capacity. Two closure plugs included. Ground screws installed. Internal threads and hubs comply with NEMA requirements. Hubs accept all threaded fittings and threaded conduit. 2" depth x 4-1/2" length x 2-3/4" width. UL Listed.
Hubbell 5321-0 Outlet Box Bell Raco 5611-0 Replacement Outer Gasket Bell Raco 5103-0 1-Hole Weatherproof Device Cover
GFCI VERT 1G COVER GRAY
Our Price : $5.39
Constructed of die-cast aluminum. For use in branch circuit wiring in wet, damp or dry locations. May be used as a weatherproof junction box or as a housing for receptacles, switches, and GFCIs. Reinforced connector outlets. Powder coat finish. Eight box mounting options with detachable lugs provided. Two closure plugs included. Ground screw installed. Four 1/2" threaded outlets. Complies with NEMA requirements. Hubs accept all threaded fittings and threaded conduit. Multi-lingual instructions. 2" depth. 18.3 cubic inch capacity. 4-1/2" length x 2-3/4" width. UL Listed. NEMA 3R rated. Replacement gasket for Bell lampholders. UL Standard CSA Certified. Includes installation hardware, gasket, and multi-lingual instructions. Weatherproof protection for outdoor receptacle. Powder coat finish for weather. Scratch resistance. Self-closing lid protects receptacle when not in use. C/UL/US NEMA 3R rated. Shrink wrapped.
Bell Raco 5103-1 1-Hole Weatherproof Device Cover Bell Raco 5320-5 Outlet Box Bell Raco 5103-2 1-Hole Weatherproof Device Cover
Includes installation hardware, gasket, and multi-lingual instructions. Weatherproof protection for outdoor receptacle. Powder coat finish for weather. Scratch resistance. Self-closing lid protects receptacle when not in use. C/UL/US NEMA 3R rated. Shrink wrapped. For use in wet, damp or dry locations. Three 1/2" threaded outlets. 2" deep with lugs. May be used as a weatherproof junction box, or as a housing for receptacles, switches, and GFCIs. Powder coat finish. Eight box mounting options with detachable lugs provided. Includes two closure plugs. Ground screw installed. Multi-lingual instructions. Internal threads and hubs comply with NEMA requirements. Hubs accept all threaded fittings and threaded conduit. Die cast aluminum construction. 18.3 cubic inch capacity. 2" depth x 4-1/2" length x 2-3/4" width. UL Listed. NEMA 3R rated. Includes installation hardware, gasket, and multi-lingual instructions. Weatherproof protection for outdoor receptacle. Powder coat finish for weather. Scratch resistance. Self-closing lid protects receptacle when not in use. C/UL/US NEMA 3R rated. Shrink wrapped.
Bell Raco 5146-0 1-Hole Weatherproof Device Cover Bell Raco 5321-2 Weatherproof Box Arrow Hart S2966W-SP Decorative Weatherproof Cover
Waterproof protection for outside receptacle. Metallic construction, powder coat finish. Scratch resistant. Self-closing lid when not in use. Includes installation hardware, gasket, and multi-lingual instructions.  4-1/2" length x 2-3/4" width. C/UL/US UL 514-A listed, File E195978 (5132-5146) CSA C22.2 No. 18 (5132-5146) NEMA 3R rated. Constructed of die-cast aluminum. For use in branch circuit wiring in wet, damp or dry locations. May be used as a weatherproof junction box or as a housing for receptacles, switches, and GFCIs. Reinforced connector outlets. Powder coat finish. Eight box mounting options with detachable lugs provided. Two closure plugs included. Ground screw installed. Four 1/2" threaded outlets. Complies with NEMA requirements. Hubs accept all threaded fittings and threaded conduit. Multi-lingual instructions. 2" depth. 18.3 cubic inch capacity. 4-1/2" length x 2-3/4" width. UL Listed. NEMA 3R rated. Plastic, impact and sunlight resistant. Gaskets provided to seal cover edges as well as device openings. Self closing cover. Stainless steel mounting screws furnished. Vertical, flush or surface mount. UL Listed.
Arrow Hart S3966W-SP Decorative Weatherproof Cover Carlon E98DHGN-CAR Weatherproof Cover Arrow Hart S2966 Decorative Weatherproof Cover
For GFCI/Decorator receptacle used in wet locations. Gaskets provided to seal cover edges as well as device openings. Stainless steel mounting screws included. Horizontal flush or surface mount. UL Listed. Non-conductive, corrosion resistant, and paintable for safe installation and operation in wet or damp locations. NEMA 3R rated and UL Listed. Plastic, impact and sunlight resistant. Gaskets provided to seal cover edges as well as device openings. Self closing cover. Stainless steel mounting screws furnished. Vertical, flush or surface mount. UL Listed.
Arrow Hart S3966 Decorative Weatherproof Cover Hubbell 5121-5 Weatherproof Device Cover Hubbell 5101-6 Weatherproof Device Cover
For GFCI/Decorator receptacle used in wet locations. Gaskets provided to seal cover edges as well as device openings. Stainless steel mounting screws included. Horizontal flush or surface mount. UL Listed. For use whenever weatherproof protection is required for an "on/off" type switch. Powder coat finish. Supplied with a switch unassembled to the cover - no need to purchase separate components. Includes installation hardware and multi-lingual instructions. Size 4-1/2" length x 2-3/4" width. UL Listed, CSA, NEMA 3R Rated. For outdoor horizontal use. Powder coat finish. Scratch resistant. Self-closing lid assures protection when receptacle is not in use. Includes installation hardware, gasket, and multi-lingual instructions. UL 514-A listed, File E 195978 C/UL CSA C22.2 No. 18  NEMA 3R rated.
Bell Raco 5321-1 Weatherproof Box Bell Raco 5101-2 1-Hole Weatherproof Device Cover Bell Raco 5101-1 1-Hole Weatherproof Device Cover
Constructed of die-cast aluminum. For use in branch circuit wiring in wet, damp or dry locations. May be used as a weatherproof junction box or as a housing for receptacles, switches, and GFCIs. Reinforced connector outlets. Powder coat finish. Eight box mounting options with detachable lugs provided. Two closure plugs included. Ground screw installed. Four 1/2" threaded outlets. Complies with NEMA requirements. Hubs accept all threaded fittings and threaded conduit. Multi-lingual instructions. 2" depth. 18.3 cubic inch capacity. 4-1/2" length x 2-3/4" width. UL Listed. NEMA 3R rated. For outdoor horizontal use. Powder coat finish. Scratch resistant. Self-closing lid assures protection when receptacle is not in use. Includes installation hardware, gasket, and multi-lingual instructions. UL 514-A listed, File E 195978 C/UL CSA C22.2 No. 18  NEMA 3R rated. For outdoor horizontal use. Powder coat finish. Scratch resistant. Self-closing lid assures protection when receptacle is not in use. Includes installation hardware, gasket, and multi-lingual instructions. UL 514-A listed, File E 195978 C/UL CSA C22.2 No. 18  NEMA 3R rated.
Spot-Gro 5330-0 Weatherproof Box Hubbell 5361-0 Splice Box Bell Raco 5324-5 Outlet Box
With lugs. Die cast aluminum. For use in branch circuit wiring in wet, damp, or dry locations. May be used as a weatherproof junction box, or as housing for receptacles, switches, and GFCI's. Eight box mounting options with detachable lugs provided. Powder coat finish. 16.5 cubic inch capacity. Two closure plugs included. Ground screw installed. Internal threads and hubs comply with NEMA requirements. Hubs accept all threaded fittings and threaded conduit. 2" depth x 4-1/2" length x 2-3/4" width. UL Listed. Shrink wrapped. For use in branch circuit wiring in wet, damp, or dry locations. Designed for use as a weatherproof junction box, and used with Bell round cluster covers and round lampholder combinations. Die cast aluminum construction. Powder coat finish. Reinforced connector outlets. Cast-in mounting lugs, four closure plugs included, and installed ground screw. 16.1 cubic inch capacity. Six 10-24 tapped holes. 4" diameter x 1-1/2" depth. UL Listed. With lugs. Die cast aluminum. For use in branch circuit wiring in wet, damp, or dry locations. May be used as a weatherproof junction box, or as housing for receptacles, switches, and GFCI's. Eight box mounting options with detachable lugs provided. Three threaded 3/4" outlets. Powder coat finish. 18.3 cubic inch capacity. Two closure plugs included. Ground screws installed. Internal threads and hubs comply with NEMA requirements. Hubs accept all threaded fittings and threaded conduit. 2" depth x 4-1/2" length x 2-3/4" width. UL Listed.
Bell Raco 5146-5 Weatherproof Device Cover Bell Raco 5322-0 Weatherproof Box Thomas & Betts E381DR Type T Weatherproof Switch Box
Waterproof protection for outside receptacle. Metallic construction, powder coat finish. Scratch resistant. Self-closing lid when not in use. Includes installation hardware, gasket, and multi-lingual instructions.  4-1/2" length x 2-3/4" width. C/UL/US UL 514-A listed, File E195978 (5132-5146) CSA C22.2 No. 18 (5132-5146) NEMA 3R rated. Weatherproof box, with lugs. Five 1/2" threaded outlets. For use in branch circuit wiring in wet, damp or dry locations. May be used as a weatherproof junction box or as a housing for receptacles, switches and GFCIs. Die cast aluminum construction. Reinforced connector outlets. Powder coat finish. Eight box mounting options with detachable lugs provided. Two closure plugs included. Ground screw installed. Internal threads and hubs comply with NEMA requirements. Hubs accept all threaded fittings and threaded conduit. Multi-lingual instructions. 2" depth x 4-1/2" length x 2-3/4" width. 18.3 cubic inch capacity. UL Listed. CSA 22.2 No. 18 NEMA 3R Rated. Weatherproof, for use with nonmetalic wiring systems. Nonconductive, noncorrosive, and impact resistant for a safe, long, service-free life in exposed applications. Install in accordance with NEC and local codes. Three 1/2" threaded ports, one on each end and one in the back. UL Listed.
Arrow Hart S992 Weatherproof Cover Bell Raco 5121-1 Weatherproof Switch Cover Carlon E98SRCN-CAR Weatherproof Cover
For single devices, take either single receptacle or switch. Corrosion resistant materials suitable for exposure to weather. Gaskets provided to seal cover edges and openings. Mount on flush or surface single gang boxes. Gray color. UL Listed. Polybagged. For use whenever weatherproof protection is required for an "on/off" type switch. Powder coat finish. Supplied with a switch unassembled to the cover - no need to purchase separate components. Includes installation hardware and multi-lingual instructions. Size 4-1/2" length x 2-3/4" width. UL Listed, CSA, NEMA 3R Rated. For 15 amp or other single receptacles under 1.375" diameter. Non-conductive, corrosion resistant, and paintable for safe installation and operation in wet or damp locations. NEMA 3R rated and UL Listed.
Carlon E98G5FN-CAR Weatherproof Cover Carlon E98GFCN-CAR Weatherproof Device Cover Carlon E98SSCN-CAR Weatherproof Cover
For 50 amp twist lock single receptacles under 2.250" diameter. For exposed applications. Will not rust or corrode. Gaskets and screws included. UL Listed. Non-conductive, corrosion resistant, and paintable for safe installation and operation in wet or damp locations. NEMA 3R rated and UL Listed. 2.63" high x 1.31" wide opening. Non-conductive. Suitable for wet locations. Gaskets and screws included. UL Listed.
Carlon E98GDRN-CAR Weatherproof Device Cover Hubbell 5361-6 Splice Box Hubbell 5101-5 Weatherproof Device Cover
Non-conductive, corrosion resistant, and paintable for safe installation and operation in wet or damp locations. NEMA 3R rated and UL Listed. For use in branch circuit wiring in wet, damp, or dry locations. Designed for use as a weatherproof junction box, and used with Bell round cluster covers and round lampholder combinations. Die cast aluminum construction. Powder coat finish. Reinforced connector outlets. Cast-in mounting lugs, four closure plugs included, and installed ground screw. 16.1 cubic inch capacity. Six 10-24 tapped holes. 4" diameter x 1-1/2" depth. UL Listed. For outdoor horizontal use. Powder coat finish. Scratch resistant. Self-closing lid assures protection when receptacle is not in use. Includes installation hardware, gasket, and multi-lingual instructions. UL 514-A listed, File E 195978 C/UL CSA C22.2 No. 18  NEMA 3R rated.
Bell Raco 5331-0 Weatherproof Box Raco 2002FBAR Vapor Barrier Box Bell Raco 5141-0 Weatherproof Switch Cover
With lugs. Die cast aluminum. For use in branch circuit wiring in wet, damp, or dry locations. May be used as a weatherproof junction box, or as housing for receptacles, switches, and GFCI's. Eight box mounting options with detachable lugs provided. Five 3/4" threaded outlets. Powder coat finish. 18.3 cubic inch capacity. Two closure plugs included. Ground screws installed. Internal threads and hubs comply with NEMA requirements. Hubs accept all threaded fittings and threaded conduit. 2" depth x 4-1/2" length x 2-3/4" width. UL Listed, CSA Approved and NEMA 3R Rated. Made from rugged polycarbonate material, yellow color, gasket seals all openings to prevent air or vapor penetration. Front-mounted ground screw, 1/2" setback, flush bracket. Self-clamping, nonmetallic sheathed cable entry tabs. Weatherproof protection for an "on-off" type switch. Vertical, mounted to device. Rugged die cast construction, powder coat finish. Self-closing lid assures weatherproof protection when not in use. Supplied with a switch - no need to purchase separate components. Switch is unassembled to the cover. UL, CSA and NEMA 3R rated. Shrink wrapped.
Carlon E9G2SSNR Weatherproof Cover Arrow Hart S989-SP Weatherproof Cover Hubbell 5323-0 Outlet Box
Weather resistant cover for double toggle switch applications. Vertical mount. UV resistant, suitable for outdoor use. Nonmetallic/noncorrosive, won't rust or fade, paintable. UL Marine Listed, CSA Certified. Corrosion resistant materials suitable for exposure to weather. Gaskets provided to seal cover edges and openings. Corrosion resistant mounting screws included. Mount on flush or surface single gang boxes. UL Listed. With lugs. Die cast aluminum. For use in branch circuit wiring in wet, damp, or dry locations. May be used as a weatherproof junction box, or as housing for receptacles, switches, and GFCIs. 5 reinforced 1/2" threaded connector outlets. Powder coat finish. Two closure plugs included. Ground screws installed. Internal threads and hubs comply with NEMA requirements. 2" depth x 4-1/2" length x 2-3/4" width. 18.3 cubic inch capacity. UL Listed.
Carlon Code Keeper Red Dot CKNM-NG Weatherproof Cover Bell Raco 5361-2 Splice Box Bell Raco 5624-1 Combination Weatherproof Lampholder
Accepts GFCI, duplex, switch and up to 1-3/8" round devices. Nonconductive, noncorrosive, and impact resistant. Won't rust or fade. Scratch resistant. For use in wet/damp locations. Keyhole mounts, loosen the existing device screws and slide the cover over. Comes with adapter plates and pre-adhered gaskets. Wasp guard included to keep out unwanted pests. Lockable for security. UL Listed. For use in branch circuit wiring in wet, damp, or dry locations. Designed for use as a weatherproof junction box, and used with Bell round cluster covers and round lampholder combinations. Die cast aluminum construction. Powder coat finish. Reinforced connector outlets. Cast-in mounting lugs, four closure plugs included, and installed ground screw. 16.1 cubic inch capacity. Six 10-24 tapped holes. 4" diameter x 1-1/2" depth. UL Listed. Die cast zinc round 4" cover and lampholder combination. Powder coat finish, scratch-resistant. For wet locations. Includes installation hardware, gasket, and multi-lingual instructions. Uses 75-150 watt maximum, Par-38 lamps, not included. UL Listed 1598 C/UL.
Raco 5372-0 Weatherproof Splice Box Hubbell 5361-5 Splice Box Bell Raco 5624 Combination Weatherproof Lampholder
For use in branch circuit wiring in wet, damp, or dry locations. Designed for use as a weatherproof junction box, and used with Bell round cluster covers and round lampholder combinations. Die cast aluminum construction. Powder coat finish. Reinforced connector outlets. Cast-in mounting lugs, four closure plugs included, and installed ground screw. 4" diameter x 1-1/2" depth. UL Listed. NEMA 3R Rated. For use in branch circuit wiring in wet, damp, or dry locations. Designed for use as a weatherproof junction box, and used with Bell round cluster covers and round lampholder combinations. Die cast aluminum construction. Powder coat finish. Reinforced connector outlets. Cast-in mounting lugs, four closure plugs included, and installed ground screw. 16.1 cubic inch capacity. Six 10-24 tapped holes. 4" diameter x 1-1/2" depth. UL Listed. Die cast zinc round 4" cover and lampholder combination. Powder coat finish, scratch-resistant. For wet locations. Includes installation hardware, gasket, and multi-lingual instructions. Uses 75-150 watt maximum, Par-38 lamps, not included. UL Listed 1598 C/UL.
Bell Raco 5361-1 Single Ended Splice Box COVER OUTLET OTDR 1 TO 3-1/2IN Arrow Hart 1113-SP 3-Hole Weatherproof Outlet Box
For use in branch circuit wiring in wet, damp, or dry locations. Designed for use as a weatherproof junction box, and used with Bell round cluster covers and round lampholder combinations. Die cast aluminum construction. Powder coat finish. Reinforced connector outlets. Cast-in mounting lugs, four closure plugs included, and installed ground screw. 16.1 cubic inch capacity. Six 10-24 tapped holes. 4" diameter x 1-1/2" depth. UL Listed. Low profile design that is expandable for weatherproof protection while an outlet is in use. Horizontal/vertical 16-in-1. Expands from 1" to 3" for while-in-use needs. 100 percent paintable surface. Polycarbonate and synthetic neoprene rubber that will not dry rot, crack or deteriorate in sunlight. Patented quick-fit keyhole mounting system allows installation in under a minute. Includes attached gasket and mounting hardware. UL Listed, NEMA 3R Rated. Electrostatically painted with a baked, weather-resistant powder finish. Accept single gang weatherproof covers and standard FS covers. Mounting lugs provide strength and durability on any mounting surface. Raised knockout studs on back of box provide alternative means for wall mounting. Strike desired studs with sharp hammer blow for clean mounting holes. Ground screw hole located inside back wall of box. Threaded outlets for conduit and connectors. Two closure plugs and mounting lugs furnished. Three holes, one at each end and one on the back. 2" depth x 2.812" width x 4.562" length. UL Listed. Carded.
Bell Rayntite 5034-0 Weatherproof Device Cover Bell Raco 5624-6 Combination Weatherproof Lampholder Hubbell 5624 Weatherproof Combination Lampholder
For weatherproof 30-50 amp receptacles and wet locations. 2.625" diameter. Die cast aluminum construction, powder coat finish. Scratch resistant. Self-closing lid assures protection when the receptacle is not in use. Padlockable. May be mounted to box or device. Includes installation hardware, gasket, and multi-lingual instructions. UL listed 514-A , File E 195978 CSA C22.2 No. 18 NEMA 3R rated. Shrink wrapped. Die cast zinc round 4" cover and lampholder combination. Powder coat finish, scratch-resistant. For wet locations. Includes installation hardware, gasket, and multi-lingual instructions. Uses 75-150 watt maximum, Par-38 lamps, not included. UL Listed 1598 C/UL. Die cast zinc round 4" cover and lampholder combination. Powder coat finish, scratch-resistant. For wet locations. Includes installation hardware, gasket, and multi-lingual instructions. Uses 75-150 watt maximum, Par-38 lamps, not included. UL Listed 1598 C/UL.
Hubbell 5621 Weatherproof Combination Lampholder Hubbell 5621 Weatherproof Combination Lampholder Bell 5400-0 Extension Adapter
Die cast zinc with rectangular cover and porcelain sockets. For wet locations. Use 75-150 watt maximum, Par-38 lamps, not included. Includes gasket, screws and plugs. UL Listed. Die cast zinc with rectangular cover and porcelain sockets. For wet locations. Use 75-150 watt maximum, Par-38 lamps, not included. Includes gasket, screws and plugs. UL Listed. Used to provide additional capacity needed for NEC box fill requirements. Die cast aluminum construction. 6 threaded 1/2" outlets. Installation hardware gasket and 1/2" closure plugs included. Ground screw is provided. Internal threads and hubs comply with NEMA requirements. Hubs accept all threaded 1/2" fittings and threaded conduit. 5-1/4" length x 3-1/2" width x 1-1/2" depth. UL Listed. NEMA 3R Rated.
Taymac MM410C Weatherproof Receptacle Cover Bell Raco 5625-2 Combination Weatherproof Lampholder Bell Rayntite 5030-0 Weatherproof Cover
Taymac Receptacle Cover, Non-Metallic, Weatherproof, 5-1/2 in Length, 2-3/4 in Width, 1 Gangs, Polycarbonate, Clear, Horizontal, Vertical Mounting, NEMA 3R, Includes: Gasket and Mounting Hardware, UL E116141, 2014 NEC Compliant, 16-in-1 Standard Configuration Die cast zinc with round 4" cover and porcelain sockets. For wet locations. Use 75-150 watt maximum, Par-38 lamps, not included. Includes multi-lingual instructions, gasket, screws and plugs. UL Listed. For 30-50 amp receptacles, 2.150" diameter. Die cast aluminum construction, powder coat finish. Scratch resistant. Self-closing lid assures protection when not in use. Padlockable. May be mounted to box or device. Includes installation hardware, gasket, and multi-lingual instructions. UL listed NEMA 3R rated.
Thomas & Betts E382DE Type T Threaded Switch Box Bell Raco 5625 Combination Weatherproof Lampholder Hubbell 5625 Weatherproof Combination Lampholder
For use with nonmetalic wiring systems. Nonconductive, noncorrosive, and impact resistant for a safe, long, service-free life in exposed applications. Install in accordance with NEC and local codes. Three 1/2" plus four 3/4" threaded ports. UL Listed. Die cast zinc with round 4" cover and porcelain sockets. For wet locations. Use 75-150 watt maximum, Par-38 lamps, not included. Includes multi-lingual instructions, gasket, screws and plugs. UL Listed. Die cast zinc with round 4" cover and porcelain sockets. For wet locations. Use 75-150 watt maximum, Par-38 lamps, not included. Includes multi-lingual instructions, gasket, screws and plugs. UL Listed.
Hubbell 5148-5 Weatherproof Device Cover Bell Raco 5625 Combination Weatherproof Lampholder Hubbell 5625 Weatherproof Combination Lampholder
Waterproof protection for outside receptacle. Self-closing lids. Installation hardware, gasket, and multi-lingual instructions included. Size: 4-1/2" width x 4-1/2" length. C/UL/US UL 514-A listed, CSA and NEMA 3R rated. Die cast zinc with round 4" cover and porcelain sockets. For wet locations. Use 75-150 watt maximum, Par-38 lamps, not included. Includes multi-lingual instructions, gasket, screws and plugs. UL Listed. Die cast zinc with round 4" cover and porcelain sockets. For wet locations. Use 75-150 watt maximum, Par-38 lamps, not included. Includes multi-lingual instructions, gasket, screws and plugs. UL Listed.
Bell Raco 5148-0 Weatherproof Device Cover Carlon E9G2DSN-CAR Weatherproof Device Cover Arrow Hart 1116-SP 3-Hole Weatherproof Outlet Box
Waterproof protection for outside receptacle. Self-closing lids. Installation hardware, gasket, and multi-lingual instructions included. Size: 4-1/2" width x 4-1/2" length. C/UL/US UL 514-A listed, CSA and NEMA 3R rated. For two gang duplex receptacles and weatherproof toggle switch applications. Electrostatically painted with a baked, weather-resistant powder finish. Accept single gang weatherproof covers and standard FS covers. Mounting lugs provide strength and durability on any mounting surface. Raised knockout studs on back of box provide alternative means for wall mounting. Strike desired studs with sharp hammer blow for clean mounting holes. Ground screw hole located inside back wall of box. Threaded outlets for conduit and connectors. Two closure plugs and mounting lugs furnished. Three holes, one at each end and one on the back. 2" depth x 2.812" width x 4.562" length. UL Listed. Carded.
Raco 5341-0 Square Weatherproof Outlet Box Hubbell 5337-5 Outlet Box Hubbell 5400-5 Extension Box Adapter
With lugs. Die cast aluminum. For use in branch circuit wiring in wet, damp, or dry locations. May be used as a weatherproof junction box or as housing for receptacles, switches and GFCI's. Eight box mounting options with detachable lugs provided. 2" deep, three 3/4" threaded outlets. 32 cubic inch capacity. Powder coat finish. Two closure plugs included. Ground screw installed. Internal threads and hubs comply with NEMA requirements. Hubs accept all threaded fittings and threaded conduit. UL Listed, CSA Approved and NEMA 3R Rated. For use in branch circuit wiring in wet, damp, or dry locations. Can be used as a weatherproof junction box, or as a housing for receptacles, switches and GFCIs. Die cast aluminum construction. Reinforced connector outlets. Powder coat finish. Eight box mounting options with detachable lugs provided. Five 1/2" threaded outlets. 31.0 cubic inch capacity. Two closure plugs included. Ground screw installed. Internal threads and hubs comply with NEMA requirements. Hubs accept all threaded fittings and threaded conduit. 2" depth x 4-1/2" length x 4-9/16" width. Multi-lingual instructions. UL Listed. NEMA 3R Rated. Used to provide additional capacity needed for NEC box fill requirements. Die cast aluminum construction. 6 threaded 1/2" outlets. Installation hardware gasket and 1/2" closure plugs included. Ground screw is provided. Internal threads and hubs comply with NEMA requirements. Hubs accept all threaded 1/2" fittings and threaded conduit. 5-1/4" length x 3-1/2" width x 1-1/2" depth. UL Listed. NEMA 3R Rated.
Rayntite 5028-5 Weatherproof Device Cover Bell 5363-0 Round Weatherproof Extension Adapter Bell Rayntite 5028-6 Weatherproof Weatherproof Device Cover
For outdoor GFCI receptacles and wet locations. Die cast aluminum construction, powder coat finish. Scratch resistant. Self-closing lid assures protection when not in use. Padlockable. May be mounted to box or device. Includes installation hardware, gasket, and multi-lingual instructions. 4-1/2" length x 2-3/4" width. UL listed 514-A , File E 195978 CSA C22.2 No. 18 NEMA 3R rated. Used to provide additional capacity. Die cast aluminum construction. Includes installation hardware, closure plugs, gasket, and multi-lingual instructions.  Four 1/2" threaded outlets. Accepts all threaded 1/2" fittings and threaded conduit. 4" Round, 1-1/2" Deep. UL listed, CSA, NEMA 3R rated. Shrink wrapped. For outdoor GFCI receptacles and wet locations. Die cast aluminum construction, powder coat finish. Scratch resistant. Self-closing lid assures protection when not in use. Padlockable. May be mounted to box or device. Includes installation hardware, gasket, and multi-lingual instructions. 4-1/2" length x 2-3/4" width. UL listed 514-A , File E 195978 CSA C22.2 No. 18 NEMA 3R rated.
Carlon Code Keeper Red Dot CKNM-NGD Clip-On Weatherproof Cover Bell Raco 5157-0 Round Weatherproof Device Cover Bell 5145-0 Weatherproof Cover 4-1/2 in L x 4-9/16 in W
Accepts GFCI, duplex, switch and up to 1-3/8" round devices. Nonconductive, noncorrosive, and impact resistant. Won't rust or fade. Scratch resistant. For use in wet/damp locations. Keyhole mounts, loosen the existing device screws and slide the cover over. Comes with adapter plates and pre-adhered gaskets. Wasp guard included to keep out unwanted pests. Lockable for security. UL Listed. Powder coat finish and scratch resistant. Weatherproof protection for outdoor receptacles. Self-closing lids assure weatherproof protection when the receptacle is not in use. Includes installation hardware, gasket, and multi-lingual instructions. 2 single, 1.406" diameter receptacle openings. C/UL/US UL 514-A listed, CSA C22.2 No. 18, NEMA 3R Rated. Shrink pack. Cast cover for use whenever weatherproof protection is required for an outdoor receptacle. Heavy duty metallic construction will last the life of the installation. Self closing lids assure weatherproof protection when the receptacle is not in use. Comes with installation instructions, gasket and hardware. UL, CSA Compliant.
Bell Raco 5333-0 Weatherproof Box Bell Raco 5337-1 Weatherproof Box Arrow Hart WIU-1 Self-Closing Weatherproof Cover
With lugs. Die cast aluminum. For use in branch circuit wiring in wet, damp or dry locations. May be used as a weatherproof junction box, or as housing for receptacles, switches and GFCI's. Eight box mounting options with detachable lugs provided. Three 1/2" threaded outlets. Powder coat finish. 32 cubic inch capacity. Two closure plugs included. Ground screw installed. Internal threads and hubs comply with NEMA requirements. Hubs accept all threaded fittings and threaded conduit. 4-1/2" x 4-1/2" x 2" deep. UL Listed, CSA Approved and NEMA 3R Rated. For use in branch circuit wiring in wet, damp, or dry locations. Can be used as a weatherproof junction box, or as a housing for receptacles, switches and GFCIs. Die cast aluminum construction. Reinforced connector outlets. Powder coat finish. Eight box mounting options with detachable lugs provided. Five 1/2" threaded outlets. 31.0 cubic inch capacity. Two closure plugs included. Ground screw installed. Internal threads and hubs comply with NEMA requirements. Hubs accept all threaded fittings and threaded conduit. 2" depth x 4-1/2" length x 4-9/16" width. Multi-lingual instructions. UL Listed. NEMA 3R Rated. UV resistant polycarbonate back, see-through self closing cover and pre-mounted gasket protect against rain, sleet and snow without cracking or breaking. Non-corrosive and non-conductive. Snap-in inserts for flexibility. Moveable hinges mount either horizontally or vertically in vinyl, brick, stucco or concrete. Meets and exceeds UL outdoor low voltage landscape lighting requirements. Meets 1999 NEC Article 210-60 (b) for hotels and motels requiring covered receptacles behind beds, and 2002 NEC Article 406.8 (B) (1) for receptacles in damp or wet locations. Comes standard with three inserts (for a total of 16 different configurations): duplex, decorator and a toggle/five receptacle opening. Receptacle sizes are: 1.25" (31.75mm), 1.375" (34.925mm), 1.625" (41.275mm), 1.75" (44.45mm), and 2.125" (54.00mm). 3.25" deep x 6.085" x 4.446". UL and cUL listed, meets NEMA 3R requirements.
Bell Raco 5337-0 Infrared Brooder Weatherproof Box Carlon Code Keeper Red Dot 2CKNM-NG Weatherproof Device Cover Raco Rayntite 5775-0 Multi Directional Weatherproof Cover
For use in branch circuit wiring in wet, damp, or dry locations. Can be used as a weatherproof junction box, or as a housing for receptacles, switches and GFCIs. Die cast aluminum construction. Reinforced connector outlets. Powder coat finish. Eight box mounting options with detachable lugs provided. Five 1/2" threaded outlets. 31.0 cubic inch capacity. Two closure plugs included. Ground screw installed. Internal threads and hubs comply with NEMA requirements. Hubs accept all threaded fittings and threaded conduit. 2" depth x 4-1/2" length x 4-9/16" width. Multi-lingual instructions. UL Listed. NEMA 3R Rated. Accepts GFCI, duplex, switch and up to 1-3/8" round devices. Nonconductive, noncorrosive, and impact resistant. Won't rust or fade. Scratch resistant. For use in wet/damp locations. Keyhole mounts, loosen the existing device screws and slide the cover over. Comes with adapter plates and pre-adhered gaskets. Wasp guard included to keep out unwanted pests. Lockable for security. UL Listed. High-impact polycarbonate construction, virtually indestructible, will not rust or corrode. 2-3/4 inch depth, 2 gang, pre-configured for GFCI with patented Knockout technology for alternate devices. 55 in 1 multiple combinations of duplex, GFCI, switch, and rounds: 1-1/4", 1-3/8", 1-9/16", 1-5/8", 1-11/16", 1-3/4, 2-1/8", 2-1/4", 2-7/16". Clear lid. Lockable design prevents tampering and accidental disconnects. Tri-lingual instructions. Includes attached gasket and mounting hardware. 5.54" x 5.43". Meets NEC requirements, UL Listed. NEMA 3R Rated. Shrink wrapped.
Hubbell 5839-5 Rectangular Weatherproof Device Cover Bell Raco 5338-0 Weatherproof Box COVER 2G 2-TOGGLE WP 15A GRAY
For use in wet, damp, or dry locations. One each 125 volt, 15 amp receptacle, single-gang box, cover and gasket included. UL Listed. Boxed. Outdoor electrical box, 4-1/2" x 4-1/2" x 2" deep with lugs. Seven 1/2" threaded outlets. 31.0 cubic inch capacity. For use outdoors in wet, damp or dry locations. Can be used as a weatherproof junction box, or as a housing for receptacles, switches, and GFCIs.  Die cast aluminum construction. Reinforced connector outlets. Powder coat finish. Eight box mounting options with detachable lugs provided. Two closure plugs included. Ground screw installed in box. Internal threads and hubs comply with NEMA requirements. Hubs accept all threaded fittings and conduit. Multi-lingual instructions. UL Listed. NEMA 3R Rated. For use whenever weatherproof protection is required for an "on/off" type switch. Powder coat finish. Supplied with a switch unassembled to the cover - no need to purchase separate components. Includes installation hardware and multi-lingual instructions. UL Listed, CSA, NEMA 3R Rated.
Arrow Hart WIU-2 Self-Closing Weatherproof Cover Bell Rayntite 5042-0 Weatherproof Device Cover Raco Wiegmann RSC080804RC Rainproof Pull Box Enclosure
UV Resistant polycarbonate back, see-through cover and pre-mounted gasket protect devices inside from rain, sleet and snow without cracking or breaking. Non-corrosive and non-conductive. Snap-in inserts provide flexibility. Meets and exceeds UL outdoor low voltage landscape lighting requirements. Meets 1999 NEC Article 210-60 (b) for hotels and motels requiring covered receptacles behind beds, and 2002 NEC Article 406.8 (B) (1) for receptacles in damp or wet locations. Comes standard with three inserts (for a total of 16 different configurations): GFCI, duplex/toggle and toggle/four round in these sizes: 1.25" (31.75mm), 1.375" (34.925mm), 1.625" (41.275mm) and 1.75" (44.45mm). 3.25" deep x 6.445" x 5.575". Rugged die cast construction, powder coat finish. Self-closing lid assures weatherproof protection when not in use. Padlockable, with 1/4" diameter hole. May be mounted to box or device. Includes installation hardware, gasket, and multi-lingual instructions. UL, CSA and NEMA 3R rated. Shrink wrapped. Made of 16 gauge pre-galvanized sheet steel. Junction boxes for terminating power or communication conductors. For runs of conduit for power or communication conductors. Service box for wiring devices or switch box for controlling wet location equipment. Drip shield top and smooth seamless sides, front and back. Knockouts are standard in bottom. No gasket required. Padlockable and provisions for meter seal are provided. A slip on reversible removable cover is securely fastened with screws located along bottom  edge. Gray finish. UL Listed.
POWER OUTLET BACKYD 1-GFI REC POWER OUTLET 50A 14-50R CON PK BOX/FLIP COVER 1G WP GFCI WHT
Made of corrosion-resistant galvanized steel with a dark-green finish to match natural landscape. Comes pre-assembled for immediate installation right out of the box. The rolled edge hinged door allows cords to exit freely. Offers a padlock provision to help prevent unauthorized access. Features a 'while-in-use' cover for outdoor use. Rated for 120-volt. UL Listed. Temporary RV power outlet is factory-assembled and factory-tested. Ready to use with no need to assemble individual parts. Single, heavy-gauge welded flange NEMA 3R rainproof enclosure protects against weather, vandalism and nuisance tripping. It is lockable and is engineered for maximum protection of receptacles, cords, plugs and breakers. All-in-one construction for factory assured terminations. Rolled edge door for cord protection. Manufactured from heavy G-90 zinc coated steel which resists corrosion and fading. Complies with National Electrical Code and OSHA requirements. 7" height x 5.5" width x 5.25" depth, 4.06 lb. For use in wet, damp or dry locations. Kit is a complete weatherproof installation, includes weatherproof box, cover, GFCI receptacle and multi-lingual instructions. UL Listed. C/UL Compliant.
POWER OUTLET 1SWITCH/1GFI RECP POWER OUTLET 30AMP R32U CON PK BOX/FLIP COVER 1G WP GFCI GRY
Made of corrosion-resistant galvanized steel with a dark-green finish to match natural landscape. Comes pre-assembled for immediate installation right out of the box. The rolled edge hinged door allows cords to exit freely. Offers a padlock provision to help prevent unauthorized access. Features a 'while-in-use' cover for outdoor use. Rated for 120-volt. UL Listed. Temporary RV power outlet is factory-assembled and factory-tested. Ready to use with no need to assemble individual parts. Single, heavy-gauge welded flange NEMA 3R rainproof enclosure protects against weather, vandalism and nuisance tripping. It is lockable and is engineered for maximum protection of receptacles, cords, plugs and breakers. All-in-one construction for factory assured terminations. Rolled edge door for cord protection. Manufactured from heavy G-90 zinc coated steel which resists corrosion and fading. Complies with National Electrical Code and OSHA requirements. 5.5" height x 7.5" width x 9.75" depth, 6.525 lb. For use in wet, damp or dry locations. Kit is a complete weatherproof installation, includes weatherproof box, cover, GFCI receptacle and multi-lingual instructions. UL Listed. C/UL Compliant.
   
 
1 2