Home > ELECTRICAL > ROUGH ELECTRICAL > ELECTRICAL BOXES
Sort By:
1 2
Thomas & Betts B118A Switch Box Thomas & Betts B120A-UPC Switch Box Thomas & Betts B122A-UPC Wall Box
With captive nails. Four integral clamps, two each end. Meets NEMA OS-2, UL Listed, classified for fire wall assemblies. With captive nails. Four integral clamps, two each end. Meets NEMA OS-2, UL Listed, classified for fire wall assemblies. With captive nails. Four integral clamps, two each end. Meets NEMA OS-2, UL Listed, classified for fire wall assemblies.
Carlon HB1BL Blank Handy Box Cover Carlon HB1GF Handy Outlet Box Cover Carlon HB1SW Handy Box Cover
Made of a durable polycarbonate material that is virtually indestructible. 1/2" knockout. 4.3" length x 2.38" width. UL Listed. Made of a durable polycarbonate material that is virtually indestructible. 4.3" x 2.38". UL Listed. Made of a durable polycarbonate material that is virtually indestructible. 4.3 length x 2.38 width. UL Listed.
Hubbell 8752 Square Flat Blank Electrical Box Cover Hubbell 860 Raised Blank Utility Box Cover Hubbell 865 Utility Box Cover
Rugged construction, used to close an outlet box. 4" square. Angled mounting slots allow for correction of box misalignment. UPC bar code. UL Listed. Steel box cover, blank with no knockouts. 2-5/16" wide x 4-3/16" tall. UL Listed. Steel box cover with single toggle switch opening in the center. 2-5/16" wide x 4-3/16" tall. UL Listed.
Hubbell 864 Utility Box Cover Carlon HB1DP Handy Box Cover Thomas & Betts BH122A-UPC Outlet Box
Steel box cover for duplex receptacle. Rugged construction. 2-5/16" wide x 4-3/16" tall. UL Listed. Made of a durable polycarbonate material that is virtually indestructible. 4.3" length x 2.38" width. UL Listed. Lightweight design and durable plastic. Listed for masonry walls. Safe to install and will never rust or corrode. Includes nails for quick, easy installation. 22 cubic inch rigid wall. 3-7/8" x 2-3/8" x 3-3/4". UL Listed.
Hubbell 722 Octagon Flat Blank Electrical Box Cover Thomas & Betts B114R-UPC Switch Box Raco 8977 Electrical Box Supports
Rugged construction, used to close an outlet box. Key hole mounting feature allows for installation of cover without removing box screws. UL Listed. Old work wall case. Safe, non-conductive. Two Zip-Mount retainers. Four integral clamps, two each end; mounting ears. 14 cubic inch,  2-3/4" x 2-1/4" x 4-1/8". UL Listed. Use two to mount switch box with plaster ears to hollow wall. Slips between box and wall, tabs bend inside box.
Hubbell 8753 Square Flat Electrical Box Cover Hubbell 8660 Utility Box Hubbell 863 Utility Box Cover
Steel box cover with single 1/2" knockout in the center. 4" square. Angled mounting slots allow for correction of box misalignment. UL Listed. Used for convenience outlets, switch boxes or small junction boxes. Drawn construction and raised grounding provision. Acceptable for use in 2-hour rated walls. Six 1/2" knockouts (sides). Two 1/2" knockouts (ends). Two 1/2" knockouts (bottom). 4" x 2" x 1-7/8" deep. 13.0 cubic inch capacity. UL Listed. Steel box cover with single 1.406" receptacle opening in the center. Rugged construction. 2-5/16" wide x 4-3/16" tall. UL Listed.
Hubbell 861 Utility Box Cover Carlon B112HB Handy Box Thomas & Betts B232A-UPC Outlet Box
Steel box cover with 1/2" knockout in the center. 2-5/16" wide x 4-3/16" tall. UL Listed. PVC handy box used for many wiring applications. Weather-resistant and nonconductive. Will accept metal handy box covers or nonmetallic covers. Includes hardware for quick, easy installation. New work safe, non-conductive. With captive nails. Eight integral clamps, four each side. 32 cubic inches. Meets NEMA OS-2, UL Listed, classified for fire wall assemblies. 3" depth x 4" x 3-3/4".
Thomas & Betts B520A-UPC Ceiling Box Hubbell 703 Round Flat Ceiling Pan Cover Hubbell 724 Octagon Flat Electrical Box Cover
With captive nails. 3/0 - 4/0 combination. Fixture spacing for 2-3/4" - 3", 6 integral clamps. 4" diameter non-metallic ceiling box, 20 cubic inch volume. Listed for fixture support up to 50 lb. 4" diameter x 2-1/4" depth. Meets NEMA OS-2, UL Listed. RoHS Compliance. Steel box cover with 1/2" knockout in the center. Key hole mounting feature allows for installation of cover without removing box screws. UL Listed. Steel box cover with single 1/2" knockout in the center. Key hole mounting feature allows for installation of cover without removing box screws. UL Listed.
Hubbell 8772 Square Raised Device Box Cover Hubbell 8192 Outlet Box Carlon A410R-CAR Square Electrical Box Cover
Used to close outlet box. For mounting switch or receptacle. Size 4" x 4",steel, UL Listed. Conduit wiring system. Installed in ceilings or walls for lighting fixtures, switches or receptacles. Used where multiple conductor runs are split into two or more directions to bring power to a number of electrical devices. Drawn construction and raised grounding provision for surface mount applications in ceilings or walls for lighting fixtures or receptacles. Eight 1/2"and four 3/4" conduit knockouts (sides). Two 1/2" and two 3/4" conduit knockouts (bottom). 4" square x 1-1/2" deep - 21.0 cubic inches. Acceptable for use in 2-hour rated fire walls. UL Listed. UPC bar code. Suitable for tile, plaster, sheetrock, paneling, masonry and all wall coverings. Brilliant electric blue. UL Listed.
Carlon E460R-CAR Blank Round Outlet Box Cover Hubbell 127 Octagon Box Raco 8190 Outlet Box
High impact lightweight round blank PVC cover for 4" round boxes to make junctions. UL Listed. Two 1/2" and two 3/4" conduit knockouts (sides). Two 1/2" and two 3/4" conduit knockouts (bottom). No bracket. Can be used in the installation of ceiling or wall lighting fixtures or as a junction box. Not designed for ceiling fan support. 50 pound maximum recommended static load. Acceptable for use in 2-hour fire rated walls. UL Listed. UPC bar code. Used where multiple conductor runs are split into two or more directions to bring power to a number of electrical devices. Drawn construction and raised grounding provision for exposed work or surface mount applications. Combination cover screw heads provide for faster mudring/cover installation. Twelve 1/2" conduit knockouts (sides). Four 1/2" conduit knockouts (bottom). No bracket. 4" square x 1-1/2" deep - 21.0 cubic inches. UL Listed, acceptable for use in 2-hour fire rated walls. UPC bar code.
Carlon B1EXT-CRD Electrical Box Raco 8768 Mud-Ring Raised Square Electrical Box Cover Thomas & Betts B108B-UPC Outlet Box
Extends an existing box by 1-1/8". Used to correct problems from remodeling where the wall surface is extended. Fits between the wiring device and the wall surface. Extends the switch or outlet box to flush with the wall. Works with all standard wiring devices. 2-1/4" x 3-1/4". UL Listed. Used to close outlet box. For mounting switch or receptacle. Size 4" x 4",steel, UL Listed. New work applications, shallow PVC switch box. Integral brackets. 1-1/4" depth x 2-3/8" x 3-5/8". UL Listed.
Thomas & Betts B108R-UPC Outlet Box Carlon B118B-UPC Switch Box Carlon A400R-CAR Square Blank Electrical Box Cover
Designed and listed for use with non-metallic sheathed cable. With mounting ears. Permissible for use with 90 degree C connectors. 8 cubic inch capacity. 1-1/4" depth x 2-3/8" x 3-5/8". UL Listed. Safe, non-conductive. With bracket for 3/8" to 5/8" wallboard. Steel and wood studs, 4 knockouts. 2-15/16" depth x 3-3/4" x 2-1/4". Two gang blank rise. Carlon blue color.
Carlon A420RR Raised Tubing Electrical Box Cover BOX OCTAGON 4IN 1-1/2IN DEEP  Raco 871 Wall Plate
Suitable for paneling masonry, plaster, sheetrock, tile and all wall coverings. Brilliant electric blue. UL Listed. Four 1/2" conduit knockouts (sides). Four 1/2" conduit knockouts (bottom). No bracket. Used in the installation of ceiling or wall lighting fixtures or as a junction box. 1-1/2" deep, 15.5 cubic inch capacity. Not designed for ceiling fan support. 50 pound maximum recommended static load. Acceptable for use in 2-hour fire rated walls. UL Listed. UPC bar code. Two device switch box cover. Made from unpainted, pregalvanized steel. Used with  2 toggle 2 gang switch boxes. UL 514-A Listed, File E195978 / CSA Listed, File LR-1082.
Raco 7887RAC Old Work Cable Box Raco 8756 Raised Square Open Electrical Box Cover Raco 787 Mud-Ring Flat Square Electrical Box Cover
Plaster ears, old work swing style clips secure box in wall. Integral clamps. Two hour fire rated. Mounting clips. 3" depth. 14.0 cubic inch capacity. UL Listed. Raised device cover. Used to hang light fixture from 4" square box. Not designed for ceiling fan support. Angled mounting slots allow for correction of box misalignment. Raised 5/8" - ears 2-3/4" - 4 cubic inches. UL Listed. UPC bar coded. Steel box cover, used to mount switch or receptacle. UL Listed.
Allied Moulded 1098-N Switch Box Raco 8189 Ceiling Outlet Box Allied Moulded P241 Switch Box
Thermoset-fiberglass, with angled mid-nails. Nails are installed as fastening devices. 2 hour wall and ceiling fire rating. Lightweight, non-corrosive, non-conductive, no ground required, will not melt or distort in high heat. Shatter resistant in cold temperatures. UL Listed. Welded square steel box, no bracket, installed in ceilings or walls for lighting fixtures, switches or receptacles, used where multiple conductor runs are split into two or more directions to bring power to a number of electrical devices.  TKO 1/2" and 3/4" eccentric knockouts (Per U.L. 514-A, suitable for use without a bonding jumper in circuits above or below 250 volts).  Eight 1/2" and 4, TKO side knockouts, two 1/2" and 2 TKO bottom knockouts. Combination cover screw heads provide for faster mud ring/cover installation. UL 514-A Listed, File E195978. 21.0 cubic inch capacity. Acceptable for use in 2-hour rated walls. Residential thermoplastic switch or receptacle box. With angled nails. 3-9/16" depth x 2-1/4" width x 3-3/4" height. 24 cubic inch volume. Fire rating classification of 2 hours in wall and ceiling. UL Listed.
Thomas & Betts SC100RR Low Voltage Box Raco 832 Blank Flat Square Electrical Box Cover Hubbell 731 Octagon Flat Electrical Box Cover
For telecommunications and other low voltage wiring. Suitable for old work applications. 1.18" depth x 2.18" x 3.05". Rugged construction, used to close an outlet box. Key hole mounting feature allows for installation of cover without removing box screws. 4-11/16" square. UL Listed. Steel box cover for one duplex receptacle. Key hole mounting feature allows for installation of cover without removing box screws. UL Listed.
Carlon A471RR Round Tubing Ceiling Box Extender with Round Cover Raco 791 Mud-Ring Flat Square Electrical Box Cover Raco 8769 Mud-Ring Raised Square Electrical Box Cover
Half inch raised round high impact lightweight PVC. Used with nonmetallic sheathed cable in octagon boxes. Supports 50 pounds. UL Listed. Steel box cover, 4", used to mount two switches or receptacles. UL Listed. Used to close outlet box. For mounting switches or receptacles. Size 4", UL Listed.
Hubbell 8650 Welded Utility Box Raco 8196 Electrical Box Carlon B518A-UPC Ceiling Box
Welded design allows for more working room inside box. Six 1/2" knockouts (sides). Two 1/2" knockouts (ends). Three 1/2" knockouts (bottom). Acceptable for use in 2-hour rated walls. UL Listed. Six 1/2" and 3 TKO conduit knockouts (sides). Three 1/2" and 2 TKO conduit knockouts (bottom). Combination cover screw heads provide for faster mudring/cover installation. FM bracket mounts flat on side of stud and provides a rigid, secure box installation. Square boxes are installed in ceiling or walls for lighting fixture or receptacles. 4" square x 1-1/2" deep - 21.0 cubic inches. UPC bar code. UL Listed. With captive nails. 18 cubic inch volume. Listed for fixture support up to 50 lb. 3" diameter x 2-3/4" depth. Meets NEMA OS-2, UL Listed.
Hubbell 8778 Square Raised Device Box Cover Carlon Flex-Plus A58381D-CAR ENT Flexible Raceway Switch Box Allied Moulded 1099-N Switch Box
Used to close outlet box. For mounting switches or receptacles. Size 4", UL Listed. Non-metallic, non-conductive. Punch type knockout. Quickly connects. Square, fits commercial and residential requirements. For 600 volt use in ceilings, floors, and walls in commercial, industrial and residential buildings not more than three floors above grade. Colored in brilliant electric blue. 3" x 2-1/4" x 1-7/8". UL Listed. Thermoset-fiberglass, with angled mid-nails. Nails are installed as fastening devices. 2 hour wall and ceiling fire rating. Lightweight, non-corrosive, non-conductive, no ground required, will not melt or distort in high heat. Shatter resistant in cold temperatures. UL Listed.
MUD RING 4SQ SINGLE RAISED 3/4 Thomas & Betts BH235A Outlet Box Carlon A615DE-CAR Flexible Raceway Ceiling Box
Used to close outlet box. For mounting switch or receptacle. Size 4" x 4",steel, UL Listed. PVC handy box used for many wiring applications. Weather-resistant and nonconductive. Will accept metal handy box covers or nonmetallic covers. 35 cubic inch rigid wall. Safe, non-conductive. Quick connect. 20.5 cubic inch capacity. Knockouts 1/2" x 3/4". 4" diameter x 2-1/8" depth.
Hubbell 907C Square Exposed Work Cover Raco 110 Electrical Box Hubbell 146 Octagon Box
Used to mount two duplex receptacles on a box in surface mount application. Raised 1/2". 6-1/2 cubic inch capacity. 4" square. UL Listed. Octagon box, 3-1/2" with four 1/2" side conduit knockouts and one 1/2" bottom conduit knockout. Drawn construction, can be used in the installation of ceiling or wall lighting fixtures or as a junction box. Not designed for ceiling fan support. 50 pound maximum recommended static load. 1-1/2" deep, 11.8 cubic inch capacity. UL Listed, acceptable for use in 2-hour fire rated walls. UPC bar code. With non-metallic sheathed cable clamps. Two 1/2" conduit knockouts and four cable knockouts, (sides). One 1/2" conduit knockout, (bottom). Used in the installation of ceiling or wall lighting fixtures or as a junction box. 1-1/2" deep, 15.5 cubic inch capacity. 50 pound maximum recommended static load. Not designed for ceiling fan support. Acceptable for use in 2-hour fire rated walls. UL Listed. UPC bar code.
Hubbell 8670 Welded Utility Box Thomas & Betts B618RR Ceiling Box Carlon Flex-Plus A58381E-CAR ENT Flexible Raceway Switch Box
Welded design allows for more working room inside box. Six 1/2" knockouts (sides). Two 1/2" knockouts (ends). Three 1/2" knockouts (bottom). Acceptable for use in 2-hour rated walls. UL Listed. Round old work box with 4 integral swing clamps. Three zip mount retainers. High temperature resistant. 4-1/4" diameter x 2-3/4" depth. UL Listed. Non-metallic, non-conductive. Punch type knockout. Quickly connects. Square, fits commercial and residential requirements. For 600 volt use in ceilings, floors, and walls in commercial, industrial and residential buildings not more than three floors above grade. Colored in brilliant electric blue. 3" x 2-1/4" x 1-7/8". UL Listed.
Raco 662 Drawn Utility Box Thomas & Betts B120R Outlet Box Raco 8197 Welded Electrical Box
Handy box, used for convenience outlet, switch box or small junction box. Three 1/2" knockouts (sides). Two 1/2" knockouts (ends). Three 1/2" knockouts (bottom). "TS" bracket for wood or metal studs. Gauging tabs and recessed nailing spur. 4" x 2" x 1-7/8" deep. 13.0 cubic inches. With mounting ears and swing bracket. 4 integral clamps, 2 each end. UL Listed, meets NEMA OS-2. Suitable for masonry walls, not UL Classified for Fire Resistance. PVC construction. 20 cubic inch capacity. 3-5/8" depth x 2-5/16" x 4-1/8". Square 4" steel box for lighting fixtures, switches or receptacles where multiple conductor runs are split into two or more directions to bring power to a number of electrical devices. 1-1/2" deep. 21.0 cubic inch capacity. Welded, with six 1/2" and three TKO  side knockouts, three 1/2" and two TKO  bottom knockouts. Flush FH bracket type for side mount of stud and features hooks that drive into face of wood stud for hands-free installation. UL Listed.
Carlon Super Blue BH525A-UPC Ceiling Box Hubbell 8232 Outlet Box Carlon Super Blue BH614R Old Work Ceiling Fan Box
Rigid polycarbonate box used for decorative light fixtures or low voltage devices. Made of a heat resistant thermoplastic material that is lightweight, noncorrosive and nonconductive. Captive nails, 25 cubic inch, 3" deep, large capacity boxes are perfect for specialty lighting, track lighting, or smoke/security devices. Listed for fixture support up to 50 lb. Includes mounting hardware. UL Listed. Conduit wiring system. Eight 1/2" and four TKO conduit knockouts (sides). Two 1/2" and two TKO conduit knockouts (bottom). 4" square x 2-1/8" deep, 30.3 cubic inch capacity. Combination cover screw heads provide for faster mudring/cover installation. No bracket, installed in ceilings or walls for lighting fixtures and receptacles. Acceptable for use in 2-hour rated fire walls. With UPC bar code. UL Listed. Spring metal mounting brackets. Fixture rating limit of 10 pounds. Heat resistant. 3-1/2" diameter round old/new work box base, ears and snap-in bracket. UL Listed.
Carlon A521DE ENT Flexible Raceway Outlet Box Raco 729 Flat Octagon Electrical Box Cover Hubbell 665 Utility Box Extension Ring
Non-metallic. Non-conductive. Suitable for masonry walls. 4" x 4" x 1-1/2". 1/2" and 3/4" knockouts. UL Listed. Steel box cover for single toggle switch. Key hole mounting feature allows for installation of cover without removing box screws. UL Listed. Used to add additional wiring capacity to handy box. Six 1/2" knockouts (sides) and two 1/2" knockouts (ends). 4" x 2" x 1-7/8" deep. 13.0 cubic inch capacity. UL Listed.
Carlon SC100A 1-Gang Low Voltage Mounting Bracket Carlon Super Blue BH525P Ceiling Box Thomas & Betts B121ADJ Wall Box
Backless bracket with nail on mounting and screw in bracket. Non-metallic. Non-conductive. 3.73" x 2.32". Combination ceiling box, hard shell with captive nails and grounding lug. 3" depth. Listed for fixture support up to 50 lb. 4.062" diameter x 3" depth. UL Listed. Provides simple installation and allows adjustment from 0 to 1-3/4" with the turn of a screw. Clip the included bracket onto any stud, mounts square and secure every time. Securing the bracket to the stud ensures that the box will not move. Comes preset at 1/2". 3-3/8" depth x 3-7/8" x 3-3/4". Permissible for use with 90 degree C connectors. Satisfies NEC 370-20. UL Listed 5Z74 and classified 2 Hr W/C.
Hubbell 803C Square Exposed Work Cover Hubbell 833 Square Flat Electrical Box Cover Raco 8779 Mud-Ring Raised Square Electrical Box Cover
Raised 1/2". For two toggle switches. 6-1/2 cubic inch capacity. UL Listed. Steel box cover with single 1/2" knockout in the center. 4-11/16" square. UL Listed. Used to close outlet box. For mounting switches or receptacles. Size 4", UL Listed.
Raco 473 Gangable Switch Box Raco 800C Raised Square Exposed Work Cover Hubbell 902C Square Raised Exposed Work Cover
Gangable 3" x 2" switch box, offers the option of constructing a box to hold two or more devices. Beveled corners prevent the clamp screws from protruding into the back wall. With nonmetallic sheathed cable clamps. Acceptable for use in 2-hour fire rated walls. Four cable knockouts (end). Two 1/2" conduit knockouts (end). 1/2" conduit knockouts (bottom). With leveling bumps. No plaster ears, not suitable for old work.  2-1/4" deep - 10.5 cubic inches. UL Listed. Used to mount one toggle switch on box in surface mount applications. Raised 1/2". 6-1/2 cubic inch capacity. UL Listed. For one duplex receptacle. Raised 1/2". 6-1/2 cubic inch capacity. 4" square. UL Listed.
Carlon E980CN-CAR Blank Weatherproof Cover Thomas & Betts B225R-UPC Outlet Box Hubbell 8663 Utility Box
Fits Carlon single gang FS boxes. Paintable surface with textured finish to hide scratches. Stainless steel mounting screws and gasket included. UL, CSA Listed. With mounting ears and 2 swing clamps. Suitable for masonry walls, UL Listed, not UL Classified for fire resistance. 2-3/4" depth x 3-1/8" x 3-15/16" Drawn construction and raised grounding provision for surface mount applications. Four 3/4" knockouts (sides). Two 3/4" knockouts (ends). One 3/4" knockout (bottom). 4" x 2" x 1-7/8" deep. 13.0 cubic inch capacity. UL Listed.
Thomas & Betts B344AB-UPC Outlet Box Carlon SC200RR Low Voltage Old Work Bracket Raco 528 Gangable Switch Box
With captive nails and bracket support, twelve integral clamps, six each side. 44 cubic inch capacity,  2-11/16" depth x 3-3/4" x 5-5/8". Meets NEMA OS-2, UL Listed, classified for fire wall assemblies. For installation of low-voltage devices in an existing wall. Thinner rectangular flange for faster, easier installation, less protrusion on the wall. Shallow bracket means less material, easier to work with. Can be installed vertically or horizontally. UL listed. Four cable knockouts (end). Two 1/2" conduit knockouts (end). One 1/2" conduit knockout (bottom). With non-metallic sheathed cable clamps. Leveling bumps. Less ears. 3" x 2" x 2-1/2" deep. 12.5 cubic inches. Acceptable for use in 2-hour rated fire walls. UL Listed.
Hubbell 130 Octagon Box Extension Ring Raco 8292 Ceiling Pan Box Hubbell 167 Octagon Box
Two 1/2" and two 3/4" conduit knockouts (sides). Extension rings provide a means for adding additional cubic capacity or as and outlet box for surface conduit. Non-metallic sheathed cable wiring system. Clamps in bottom. Four cable knockouts, one 1/2" conduit. 3-1/2" diameter x 1/2" depth. UL Listed. Two 1/2" and two 3/4" conduit knockouts (sides). Three 3/4" and two 1/2" conduit knockouts (bottom). No bracket. Can be used in the installation of ceiling or wall lighting fixtures or as a junction box. Not designed for ceiling fan support. 50 pound maximum recommended static load. Acceptable for use in 2-hour fire rated walls. UL Listed. UPC bar code.
Hubbell 8500 Gangable Switch Box Raco 661 Handy Box Raco 906C Surface Mount Exposed Work Cover
Conduit wiring system. Four 1/2" conduit knockouts (sides). Two 1/2" conduit knockouts (end). Two 1/2" conduit knockouts (bottom). Less clamps. 3" x 2" x 2-1/2" deep. 12.5 cubic inches. Acceptable for use in 2-hour rated fire walls. UL Listed. Three 1/2" knockouts (sides). 4" x 2" x 1-7/8" deep. 13.0 cubic inch capacity. "A" style bracket for wood or metal, positions handy box securely against face and side of stud. Acceptable for use in 2-hour rated walls. UL Listed. For one each duplex receptacle and toggle switch. 4" square. Raised 1/2". 6.5 cubic inch capacity. UL Listed.
Carlon B418A-UPC Shallow Outlet Box Carlon B117RSW Old Work Shallow Outlet Box Raco 809C Raised Square Exposed Work Cover
With captive nails and ten integral clamps, three top and bottom, two each side. Suitable for masonry walls. 4" x 4" square. UL Listed. Shallow box, flanged, non-metallic and non-conductive. 2" depth x 4-1/4" width x 4" length. For two GFCI receptacles. 6.5 cubic inch capacity. UL Listed, CSA Listed.
Hubbell 519 Gangable Switch Box Raco 400 Gangable Switch Box Raco 808C Raised Square Exposed Work Cover
Four cable knockouts (end). One 1/2" conduit knockout (bottom). With clamps for non-metallic sheathed cable. 3" x 2" x 2-1/2" deep - 12.5 cubic inches. Adjustable plaster ears allow box to be used in old work applications. Acceptable for use in 2-hour rated fire walls. Gangable 3" x 2" switch box, offers the option of constructing a box to hold two or more devices. Two 1/2" conduit knockouts (end). One 1/2" conduit knockout (bottom). Plaster ears allow the box to be used in old work applications. Acceptable for use in 2-hour rated fire walls. 1-1/2" deep - 7.5 cubic inches. UL Listed. Raised 1/2". Used to support switches or receptacles independent of the box (box must still be used). 6.5 cubic inches. UL Listed.
Hubbell 471 Gangable Switch Box Hubbell 8531 Gangable Switch Box Hubbell 8293 Ceiling Pan Box
Beveled corner box, designed to prevent the clamp screws from protruding into back wall. Non-metallic sheathed cable clamps. Acceptable for use in 2-hour rated walls. Four cable knockouts (end). One 1/2" conduit knockout (bottom). No bracket, clamp screws through beveled corners. With ears. 3" x 2" x 2-1/4" deep. 10.5 cubic inches. UL Listed. Four cable knockouts (end). Two 1/2" conduit knockouts (end). One 1/2" conduit knockout (bottom). With non-metallic sheathed cable clamps. "TS" brackets for wood or metal studs. Gauging tabs and recessed nailing spur. Side mount. 3" x 2" x 2-1/2" deep. 12.5 cubic inches. UL Listed. Five 1/2" bottom conduit knockouts, 6 cubic inch capacity. Acceptable for use in 2-hour rated walls and ceilings. 4" diameter x 1/2" depth. UL Listed.
Raco 420 Gangable Switch Box Raco 404 Non-Gangable Shallow Switch Box Hubbell 410 Non- Gangable Switch Box
Gangable 3" x 2" switch box, offers the option of constructing a box to hold two or more devices. Plaster ears allow the box to be used in old work applications. Acceptable for use in 2-hour fire rated walls. Four 1/2" conduit knockout (sides). Two 1/2" conduit knockout (end). Two 1/2" conduit knockouts (bottom). 2" deep - 10.0 cubic inches. UL Listed. Shallow switch box, made for use with furring strips and 1/4" paneling. Welded, with nonmetallic sheathed cable clamps. Two cable knockouts (end). One 1/2"' conduit knockout (end). D bracket for wood or metal studs. 1/4" bracket setback. 1" deep - 6.5 cubic inches. UL Listed. Four cable knockouts on the end. 3" x 2" x 1-1/2" deep. 7.5 cubic inches. With clamps for non-metallic sheathed cable. Plaster ears allow the box to be used in old work applications. Acceptable for use in 2-hour fire rated walls. UL Listed.
Carlon CPC4WH Blank Round Flat Outlet Box Cover Allied Moulded 9363-EWK Old Work Switch Box Carlon E9802CN-CAR Blank Square Weatherproof Cover
Non-metallic white ceiling box cover, flat and blank. 4" diameter. UL Listed. Thermoset-fiberglass with ears, wing brackets, speed clamps. 2 hour wall and ceiling fire rating. Lightweight, non-corrosive, non-conductive, no ground required, will not melt or distort in high heat. Shatter resistant in cold temperatures. 2-7/8" x 2-3/8" x 3-1/4". UL Listed. UV resistant, suitable for outdoor use. For use in wet or damp locations, UL Marine Listed. Non-metallic, non-corrosive, will not rust or fade. Fits two gang metallic and non metallic boxes. Includes stainless steel mounting screws and gasket. UL Listed.
Raco 7488RAC Old Work Cable Box Raco 567 Gangable Switch Box Raco 175 Ceiling Outlet Box
Old work PVC box. With swing clips and integral clamps to hold securely. 3-5/32" depth. 25.0 cubic inch capacity. Four 1/2" conduit knockouts (sides). Four cable knockouts (end). Two 1/2" conduit knockouts (end). One 1/2" conduit knockout (bottom). With non-metallic sheathed cable clamps. 3" x 2" x 2-3/4" deep. 14.0 cubic inches. Acceptable for use in 2-hour rated fire walls. UL Listed. With non-metallic sheathed cable clamps. Two 1/2" conduit knockouts and four cable knockouts, (sides). One 1/2" conduit knockout, (bottom). Can be used in the installation of ceiling or wall lighting fixtures or as a junction box. Not designed for ceiling fan support. 50 pound maximum recommended static load. 2-1/8" deep, 21.5 cubic inch capacity. UL Listed.
Raco 8355 Non-Gangable Switch Box Raco 810C Raised Square Exposed Work Cover Raco 920 Steel Bar Hangers
Four cable knockouts (ends). One 1/2" conduit knockout (bottom). With clamps for non-metallic sheathed cable. "S" backset. Mounting guides set 3/8", with bumps. Angle nail type. 3" x 2" x 2-27/32" deep, 15.8 cubic inch capacity. Prepositioned mounting nails included. Acceptable for use in 2-hour rated walls. UL Listed. Used to mount switches or receptacles on boxes in surface mount applications. Raised 1/2". For one 30-50 amp, single receptacle, 2.141" diameter. 6-1/2 cubic inch capacity. 4" square. UL Listed. Holding prong, box clip holds box in place for nailing. Design resists bending and twisting. With stud. Length 14-1/4" thru 22-1/2". With locking tabs to hold bar in position. UL Listed.
Raco 560 Gangable Switch Box Allied Moulded 9318 Handy Box Thomas & Betts BH353A Lightweight Outlet Box
For conduit. 3" x 2" switch box. No bracket, adjustable plaster ears allow box to be used in old work applications. 14.0  cubic inch capacity, 2-3/4" deep, four 1/2" side knockouts, two 1/2" bottom knockouts and two 1/2" end knockouts. Acceptable for use in 2-hour rated fire walls. UL Listed. Thermoset-fiberglass handy box. Surface mounted, with side and bottom romex cable openings. 2" depth x 2-1/4" width x 4-3/16" height. UL Listed. Lightweight design and durable plastic. Safe to install and will never rust or corrode. Includes hardware for easy installation. Rigid wall box.
Hubbell 8203 Electrical Box Extension Ring Thomas & Betts B620KR-UPC Ceiling Box Thomas & Betts B432A-UPC Outlet Box
For adding additional cubic capacity or as an outlet box for surface conduit. Eight 1/2" and four 3/4" conduit knockouts (sides). 4" square x 1-1/2" deep. 22.5 cubic inches. UL Listed. Ceiling box with 14.38"-22.5" adjustable bar hanger. 4" diameter x 2-1/4" depth. Fixture spacing for 2-3/4" and 3-1/2". Integral clamps. Listed for fixture support up to 50 pounds. UL Listed. With captive nails and ten integral clamps, three top and bottom, two each side. Suitable for masonry walls. 4" x 4" square. UL Listed.
Raco 976 Extension Ring Switch Box Hubbell 160 Octagon Box Raco 164 Electrical Box
Add-A-Depth ring used to correct for a 3" x 2" switch box or 4" square box (2 needed) set too deep in a wall. Adjustment range 1/4" to 1", two 1-1/8" long screws included. UPC bar code. With non-metallic sheathed cable clamps. Two 1/2" conduit knockouts and four cable knockouts, (sides). One 1/2" conduit knockout, (bottom). Can be used in the installation of ceiling or wall lighting fixtures or as a junction box. Not designed for ceiling fan support. 50 pound maximum recommended static load. J side-mount bracket with spurs and holes for toe-nailing, for wood studs or joists. UPC bar code. UL Listed. Four cable pryouts and one 1/2" KO side, one - 1/2" KO bottom. Octagon boxes are used in the installation of ceiling or wall light fixtures. TS bracket features gauging tabs and recessed nailing spurs, for wood or metal studs. Acceptable for use in 2-hour fire rated walls and ceilings. 1-1/2" deep - 15.5 cubic inches. UL Listed. UPC bar code.
Thomas & Betts B232B-UPC Outlet Box Allied Moulded 9351-NK Outlet Box Thomas & Betts SC200DV Dual Voltage Outlet Box
With bracket for 3/8" to 5/8" wallboard steel or wood stud mounting and 8 integral clamps, 4 each side. 3-3/4" x 4" x 3". Ceiling box with nails, speed clamps. 50 lb. fixture rated. 2 hour wall and ceiling fire rating classification. 4" diameter x 2-3/8" depth. UL Listed. Enables line voltage and low-voltage to run to the same location. Uses standard 2 gang faceplate. Backless design accommodates large/deep low voltage devices. 3.69" x 4.04". 20.5 cubic inch capacity. UL approved.
Raco 295 Ceiling Fan Box Raco 529 Gangable Switch Box Raco 780 Mud-Ring Raised Square Electrical Box Cover
Ceiling fan 4" round pan, 1/2" deep, 6 cubic inches, 5 bottom 1/2" knockouts. Used for new work and renovations. Ceiling fan rated, used in the installation of heavy light fixtures or ceiling fans. Maximum 70 pound fan or 150 pound fixture. Includes nonmetallic sheathed cable connector, mounting hardware, and instructions. Acceptable for use in 2-hour rated walls and ceilings. UL Listed. Four cable knockouts (end). Two 1/2" conduit knockouts, (end). One 1/2" conduit knockout (bottom). "LB" bracket for wood studs, 5/8" offset to clear narrow door molding. Face mounts on front edge of wood stud. Use when space between studs is limited. With clamps for non-metallic sheathed cable. 3" x 2" x 2-1/2" deep. 12.5 cubic inches. UL Listed. Used to close outlet box. For mounting switches or receptacles. Size 4", UL Listed.
Raco 522 Gangable Switch Box Raco TigerGrip 523 Gangable Old Work Switch Box Allied Moulded 9361-ESK Old Work Switch Box
Four cable knockouts (end). Two 1/2" conduit knockouts (end). One 1/2" conduit knockout (bottom). With armored cable/metal clad/flex clamps. "LB" bracket for wood studs, with 5/8" setback, no plaster ears. Acceptable for use in 2-hour rated walls. 2-1/2" deep - 12.5 cubic inches. UL 514-A listed, File E195978. UPC bar coded. One 1/2" bottom knockout. Four cable knockouts. 2-1/2" deep x 12.5 cubic inches. Armored cable/metal clad/flex clamps. Old work clips on side of box eliminates the need for additional box supports to secure box in wall opening. Acceptable for use in 2-hour rated walls. UL Listed. UPC bar coded. Thermoset-fiberglass with ears, snap bracket, speed clamps. Lightweight, non-corrosive, non-conductive, no ground required, will not melt or distort in high heat. Shatter resistant in cold temperatures. 2 hour wall fire rating. 2-7/8" x 2-3/8" x 3-1/4". UL Listed.
Hubbell 518 Gangable Switch Box Raco 8601 Gangable Switch Box Raco 112 Electrical Box
One 1/2" bottom conduit knockout, four bottom cable knockouts. With armored cable/metal clad/flex clamps. Adjustable plaster ears allow box to be used in old work applications. Acceptable for use in 2-hour rated walls. 2-1/2" deep - 12.5 cubic inches. UL Listed. UPC bar coded. Four 1/2" conduit knockouts (sides). Four cable knockouts (end). Two 1/2" conduit knockouts (end). One 1/2" conduit knockout (bottom). With non-metallic cable clamps in each end. 3" x 2" x 3-1/2" deep. 18.0 cubic inches. Adjustable plaster ears allow box to be used in old work applications. Acceptable for use in 2-hour rated walls. UL Listed. With non-metallic sheathed cable clamps. Two 1/2" conduit knockouts and four cable knockouts, (sides). One 1/2" conduit knockout, (bottom). Octagon boxes can be used in the installation of ceiling or wall lighting fixtures or as a junction box. Not designed for ceiling fan support. 1-1/2" deep, 11.8 cubic inch capacity. UL Listed, acceptable for use in 2-hour fire rated walls.
Raco 487 Gangable Old Work Switch Box Raco 223 Electrical Box Raco 545 Non-Gangable Old Work Switch Box
Four cable knockouts (end). One 1/2" conduit knockout (bottom). Clamp screws through beveled corners. With clamps for non-metallic sheathed cable. Adjustable plaster ears allow box to be used in old work applications. Old work clips on side of box eliminates the need for additional box supports to secure box in wall opening. 3" x 2" x 2-1/4" deep. 10.5 cubic inches. Four cable knockouts (sides). Two 1/2" and one TKO conduit knockouts (sides). One 1/2" conduit knockout (bottom). With non-metallic sheathed cable clamps. FM flush side-mount bracket for wood or metal studs. Square boxes are installed in ceilings or walls for lighting fixtures or receptacles. Acceptable for use in 2-hour fire rated walls. 4" square x 1-1/2" deep - 21.0 cubic inches. UPC bar code. UL Listed. Four cable knockouts (end). Two 1/2" knockouts (end). With NMSC, non-metallic sheathed cable clamps. Old work clip. 3" x 2" x 2-1/2" deep - 12.5 cubic inches. Acceptable for use in 2-hour rated fire walls. UL Listed.
Thomas & Betts B708-SHK Ceiling Pan Box Carlon A122 ENT Flexible Raceway Outlet Box Carlon Super Blue BH118R Old Work Outlet Box
Shallow ceiling fan outlet box with mounting screws. 1 integral clamp. Non-conductive high impact lightweight PVC. 5 knock outs, 8 cubic inch capacity. For new work or renovations. Mounts ceiling fan securely to the ceiling joist. Rated for fans up to 35 pounds and fixture up to 50 pounds. 4" diameter x 5/8" depth. UL Listed. Eccentric knockouts, non-metallic and non-conductive. Can be mounted to wood or steel studs. 3.53" height x 2.10" width x 3.25" depth. Lightweight, noncorrosive, and nonconductive, rigid, nonmetallic wiring box combines features of hard shell thermoset box and thermoplastic PVC style box. Molded of specially formulated, strong thermoplastic material, will not crack or break, even in extreme environments. Resists flexing and holds shape even under the worst conditions. Provides large wirefill capacity, and comes with molded-in nailing flanges and molded-in swing clamps to make installation faster. Designed to nest inside one another to take up less shelf space and are easier to transport to job sites. 3.85" x 2.41". UL Listed.
Hubbell 8257 Welded Outlet Box Raco 508 Non-Gangable Switch Box Raco 8211 Outlet Box
Conduit wiring system. Two 1/2" and twelve TKO conduit knockouts (sides). One 1/2", three TKO conduit knockouts (bottom). No bracket, installed in ceilings or walls for lighting fixtures or receptacles. 4-11/16" square x 2-1/8" deep - 42.0 cubic inches. Combination cover screw heads provide for faster mudring/cover installation. UPC bar code. UL Listed. Two 1/2" conduit knockouts (end). Old work clips. Provided U box support eliminates the need for additional box supports to secure box in wall opening. For 3/4" sheetrock maximum thickness. Acceptable for use in 2-hour fire rated walls. 12.5 cubic inches. 3" x 2" x 2-1/2" deep. UL Listed. Four cable knockouts (sides). Four 1/2" and two TKO conduit knockouts (sides). One 1/2" conduit knockout (bottom). With clamps for non-metallic sheathed cable. Square boxes are used where multiple conductor runs are split into two or more directions to bring power to a number of electrical devices. 4" square x 1-1/2" deep - 21.0 cubic inches. UL Listed, acceptable for use in 2-hour fire rated walls. UPC bar code.
Carlon B455A-UPC Outlet Box Allied Moulded 2300-NK Switch Box Carlon Super Blue BH525H Ceiling Box
Safe, non-metallic, non-conductive. Molded instructions. 12 integral clamps, 6 each side. Bracket and captive nails included. 2-1/2" depth x 3-7/10" x 7-3/5". Thermoset-fiberglass, with angled mid-nails, speed clamps. Lightweight, non-corrosive, non-conductive, no ground required, will not melt or distort in high heat. Shatter resistant in cold temperatures. 2 hour wall fire rating. 3" depth x 4" x 3-3/4". UL Listed. Lightweight, noncorrosive, and nonconductive, rigid, nonmetallic wiring box combines features of hard shell thermoset box and thermoplastic PVC style box. 4" diameter x 2.95" depth. Molded of specially formulated, strong thermoplastic material, will not crack or break, even in extreme environments. Resists flexing and holds shape even under the worst conditions. Provides large wirefill capacity, and comes with molded-in nailing flanges and clamps to make installation faster. Listed for fixture support up to 50 lb. Hanger bar adjusts from 11-1/2" to 18-1/2". UL Listed.
   
 
1 2